Production
가이드: 480 · 섹션: 10
생산 설정 및 워크플로53
- Lock the design to prevent clashes between design and production editsLock the design when a designer and a production person may edit it at the same time, so the designer cannot make changes until the admin or design head unlocks it.
- 동일한 설계를 공유하거나 생산 설계 사본을 생성하세요편집 내용이 자동으로 동기화되도록 동일한 설계를 공유할지, 독립적으로 유지되는 생산 설계 사본을 생성할지 결정하세요.
- Choose copy or share when sending a design to productionDecide whether to create a production design copy or share the same design when sending a design to production.
- Send a design from the design portal to productionCreate the design and drawings in the design portal, then hand it to the production portal for checking before it reaches the shop floor.
- 공유된 디자인이 Production Designs에 표시되는 방식을 이해합니다Share Same Design으로 전송한 디자인이 디자인 포털의 Production Designs에 어떻게 표시되고 디자인과 어떻게 연결된 상태로 유지되는지 알아봅니다.
- 디자인 포털에서 생산 QC 및 MES로 디자인이 흘러가는 방식디자인 포털에서 시작해 생산 팀의 QC 검사를 거쳐 MES 포털에 이르기까지 프로젝트를 따라가 보세요. MES 포털에서 산출물을 사용할 수 있게 됩니다.
모두 보기 (53)
- Publish a work order so it appears in the MES portalPublish or republish a design so its work order becomes available to the factory team in the MES portal.
- Create a production design in copy modeCreate a production design in copy mode instead of share mode.
- 생산 설계 포털에서 작업 범위를 생성하고 절단 목록에 접근하세요특정 영역의 작업 범위를 생성하여 해당 절단 목록을 생성하고 원자재 자재 명세서에 접근할 수 있습니다.
- How the production workflow runs from design to work orderFollow how a finalised design moves through production and into the work order, carrying its materials with it.
- How work orders are created and republished from design filesLearn how each design file sent to production becomes its own work order, how updates republish it, and why components stay together.
- Publish a production design as a work orderApply the hardware and connector selections on the production design, then publish it as a work order.
- 카탈로그 변경 후 출력 캐시를 새로 고치고 다시 동기화하십시오마감재 또는 심재 설정을 변경한 후에는 출력 캐시를 새로 고쳐 업데이트된 결 및 재료 속성이 절단 목록과 보드 레이아웃에 반영되도록 하십시오.
- Access production design from the main appReach production design from the main app rather than a separate production-design subdomain or portal.
- Batch rooms into one work order with work scopesUse work scopes to combine several rooms into one production run or split them into separate work orders.
- Edit channels in production design without returning to designCorrect a channel directly in the production design module after a design has been sent to production, without going back to the design module.
- Edit connector and construction changes through production designSend the design to production from Outputs, create a new production and open the production design so you can review and modify connector scenarios there.
- 디자인에서 절단 목록과 생산 출력을 생성합니다디자인에서 생산까지 하나의 흐름으로 진행하며, 별도의 2D CAD 도면 대신 모델에서 절단 목록, 하드웨어 목록, 설치 가이드를 생성합니다.
- Publish a checked cut list to a work orderPublish a confirmed cut list so you can download the work order and get the final cutting list and machine outputs.
- Publish a job to the MES portalPublish the job to the MES portal from the production design portal so it reaches production.
- Republish a design so the work order cut list is up to dateMake or verify a change in the production design and republish it so the work order cut list picks up the updated values.
- 소스 디자인에서 프로덕션 디자인 다시 동기화소스 디자인에서 프로덕션 디자인을 다시 동기화하여 유닛을 추가, 삭제, 수정하고, 확인하기 전에 영향을 검토하세요.
- Understand what a workscope is in Production > Work ScopesLearn what a workscope covers and how separate workscopes are set up for the outputs you need.
- Update and resync a design to push it to productionUpdate the design and use the resync feature to push it to production.
- Verify materials with QC and create a work orderCheck that core, finished and edge band materials are correctly applied, then create a work order and download its outputs.
- Add machines after publishing and refresh the machine listAdd a beam-saw or CNC machine in Settings > Machines and make it appear on the published work order without republishing.
- Choose which stages a job usesDecide which station types contribute to progress and leave out Packaging and Shipment for smaller jobs.
- Create work scopes as batches and publish per batchSplit production work into batches, add the relevant items to each, and publish them batch by batch to get outputs.
- Download technical documentation summary from production portal after transferGet a technical documentation summary covering part codes, dimensions, materials, finishes and edge band specifications after transferring a project to production.
- Find CAM mode in Infurnia Production, not DesignLearn where CAM mode is available and why cabinets no longer show it while you work in the Design module.
- Find your way around a production design copy's Production tabOpen a production design copy and use the Production tab toolbar and the Differences between work order and design dialog to compare the work order with the design.
- How work order numbers are assignedLearn that the work order number shown in the project is assigned by Infurnia and cannot be edited by the user.
- Limit a scenario change to the current designScope a construction or CAM scenario change to the current design instead of applying it globally.
- Pack panels into boxes and ship themScan panels into a box on the Packaging page, then complete shipment by scanning the box.
- Publish a work order after checking the cut list and board layoutCheck the cut list and board layout in the production tab, then publish the work order under a name once both are error-free.
- Publish a work order to unlock downloadsPublish the work order so its downloads become available and an immutable published design version is created.
- 기계 출력을 생성하기 전에 관리자에서 CAM 설정을 새로 고치십시오관리자가 구성한 최신 CAM 설정을 가져와 적용하면 위반 없이 기계 출력을 다운로드할 수 있습니다.
- Refresh cutlist settings from Admin and republishPull the latest cutlist settings from the Admin portal and republish the design so updated production files can be downloaded.
- 관리자에서 설정을 새로 고친 후 출력물을 다운로드하기 전에 적용하세요.최신 관리자 설정을 새로 고치고 적용한 다음, 출력 파일을 다운로드하여 출력물에 큰 문제가 없는지 확인하세요.
- Resize a unit without breaking MES calculationsChange a unit's dimensions in the design and its production calculations follow the updated size, because it stays the same unit.
- MES 릴리스 전 설계 검토생산 관리자는 설계를 검토하고 MES로 릴리스되기 전에 premilling과 같은 값을 변경할 수 있습니다.
- Review designs in the production design portal before a work orderBefore a work order is created, use the production design portal to review the design construction-wise.
- Review what changed and when in production design versionsOpen the Versions & History dialog in the production design to see each change with its action, timeline and user, so you can review what was changed on a given day.
- Send a design to production from the homepageOpen the three-dashes menu on the homepage and choose Send to Production to send your design to production.
- Send designs for production via email from the portalSend a design directly by email from the portal so it reaches production.
- Set board layout and CAM settings in manufacturing settingsConfigure board layout and CAM settings, and change manufacturing range values globally, from manufacturing settings in the admin portal.
- 생산 디자인 링크 공유생산 디자인의 디자인 링크로 일반 공유 링크를 사용하세요.
- 보관된 목록에서 제작 디자인 보관 해제보관된 제작 디자인을 Production Designs > Archived 목록에서 In Progress로 되돌립니다.
- 생산 디자이너 역할 이해하기생산 디자이너가 디자이너와 공장 팀을 어떻게 연결하고 생산 전에 설계를 검증하는지 알아보세요.
- Understand work scopes and rooms for productionLearn that sending a design to production and defining a work scope both work without any room.
- Use consistent project naming so production can identify the jobTrack each job through production by relying on the project name, designer and status.
- Use Outputs > Production Settings in the design editorOpen Outputs > Production Settings to refresh the cache, check for overlapping modular units and reassign unit, panel and cabinet finish annotations.
- 컷 리스트를 확인하고 프로젝트를 MES로 전송디자인이 확정되면 컷 리스트를 확인하고 프로젝트를 공장 생산을 위해 MES 포털로 전송합니다.
작업 지시 및 게시31
- Download board layouts, labels and pasting reportsDownload the board summary and layout files for every board type, and get panel labels, sheet labels and pasting reports as separate downloads.
- 생산 출력에서 패널 제외생산으로 보내기 전에 하위 집합을 선택하거나 패널을 숨겨 절단 목록과 일정에서 패널을 제외하세요.
- How saw file formats are chosen for the production machineLearn how the production machine's output type decides the saw file format and what the beam saw operator should check.
- Verify edge bands and cutlist before productionCheck edge bands, back panels and cutlist output in QC Mode before releasing the design.
- Download files from a published work orderOpen the published version of a work order to download raw-material CSVs and machine saw files.
- 위반 목록에서 충돌 해결모델의 충돌 표시가 목록 항목과 일치하는 위반 목록을 열고 그곳의 충돌 해결 작업을 사용하여 충돌을 해제하세요.
모두 보기 (31)
- 파티션 폭을 이동하거나 충돌을 해결하여 드릴 충돌을 해결합니다단일 유닛 CAM 모드에서 드릴 및 드릴 충돌 패널 위반을 확인한 다음, 더 큰 문제에는 solve collisions를 사용하십시오.
- 요소가 모든 출력에서 제외되는 이유 확인제외 사유를 하나씩 확인하여 요소가 모든 출력에서 누락된 이유를 찾으십시오.
- Delete all SKUs via bulk action in edit modeClear the whole SKU list in one operation instead of deleting items one by one.
- Download a machine cutlist and handle unsupported formatsOpen the Cutlist tab, pick a panel-saw machine and fall back to CSV when the machine's format is not supported.
- Find and open board layout violationsSpot board types with violations and open the read-only violations view to see the offending panels.
- 패널, 하드웨어 및 선반 충돌을 표시하는 위반 사항 수정설계에서 위반 사항이 발생하는 원인과 이를 자동 또는 수동으로 해결하는 방법을 알아보세요.
- Generate a board layout and choose Accept, Abort or Re-generateOpen the Board Layout tab to start generation, then decide whether to accept the best layout so far, abort the run, or force a fresh regeneration.
- How output quantity above 1 duplicates panels with _1/_2 labelsSet a cabinet's output quantity above one and see how its panels are laid out and labelled as copies while sharing a single CNC file per panel.
- 위반 목록에서 설계 위반 사항 읽기생산 출력을 생성하기 전에 위반 목록을 열어 보류 중인 위반 사항을 검토하십시오.
- Verify board layout before downloading machine filesCheck the board layout of a republished design so you can spot how many board types and sheets will be produced and catch mistakes before downloading machine files.
- Verify cut list and clear violations before sending to factoryQuality-check the board layout and review the cut list of panel sizes before a design goes to the factory.
- Check for clashing drill holes before productionRun collision detection in the design tool so clashing drill holes are caught before the design goes to production.
- 게시 위반 사항을 확인하여 치수가 0이거나 유효하지 않은 패널을 찾으세요생산 파일을 다운로드하기 전에 디자인을 게시하고 위반 목록을 검토하여 치수가 0이거나 유효하지 않은 패널을 찾으세요.
- 게시된 작업 지시서에서 패널 및 시트 라벨 템플릿 선택작업 지시서를 게시하면 스티커와 라벨 설정을 사용할 수 있게 됩니다. 그런 다음 보드 레이아웃에 사용할 기본 패널 및 시트 라벨 템플릿을 선택하세요.
- Edit Work Scope > Show Units에서 단위를 일괄로 비활성화Bulk Disable로 단위를 끄면 해당 단위가 Removed Units로 이동하며 카드에 재정의된 상태가 표시됩니다.
- 디자인에 대기 중인 위반 사항이 있을 때 절단 목록 PDF 다운로드디자인에 대기 중인 위반 사항이 남아 있어도 해당 위반 사항이 적용되는 범위와 검사를 확인한 후 Cut List PDF를 다운로드하세요.
- 보류 중인 위반이 있는 작업 지시서 다운로드작업 지시서에 보류 중인 위반이 남아 있으면 MES 포털은 다운로드 전에 출력이 올바르지 않을 수 있다고 경고하고, 사용자가 수행할 작업을 선택할 수 있게 합니다.
- Download board summary, layout PDF and hardware BQ after publishingAfter publishing a design, download the board summary PDF, the layout PDF and the hardware BQ so procurement and assembly have the correct documents and hardware list.
- Download the board layout as CSV and PDFOnce all quality-control checks pass, download the layout as a CSV file and a PDF for use in manufacturing.
- Exempt violations to hide production errors from designersHide production issues and errors from designers by exempting violations in the admin settings.
- 재동기화로 룸 범위가 변경된 후 유닛 복구소스 디자인과의 재동기화로 유닛이 제거된 것처럼 보이면, 확인 창에 표시된 룸 범위를 확인하고 'Units removed from manufacturing'에서 유닛을 복구하십시오.
- Resolve drill outside panel CNC violations using violation detailsOpen the violation details for a CNC violation such as drill outside panel, which are listed with codes, to resolve it.
- PD 브랜치를 다시 동기화하고 두 브랜치의 변경 사항을 모두 유지합니다PD 브랜치를 다시 동기화하여 두 브랜치에서 수행된 수정 사항을 유지하면서 업데이트합니다. 충돌하는 PD 브랜치 변경 사항은 삭제됩니다.
- Review and accept admin setting differences on a work orderSee which work order settings differ from the admin values and accept them to continue to the Violations check or a CNC machine-files download.
- 생산 설계에서 충돌 해결Violations에서 Solve collisions를 실행하면 CAM Settings에 설정된 값만큼 커넥터가 이동하며, 각 변경 사항을 검토할 수 있습니다.
절단 목록 열 및 설정65
- 재단 목록 열을 사용자 지정하고 엣지 밴드 두께를 포함하세요원하는 재단 목록 열을 설정하고 엣지 밴드 두께를 계산에 포함할지 결정하세요.
- 생산 재단 목록에서 완성 치수와 함께 재단 치수 표시선택적 재단 열을 켜면 재단 목록에서 엣지 밴딩 전 재단 치수가 완성 패널 치수 옆에 표시됩니다.
- 엣지 밴드 두께가 완성된 도어 크기에 미치는 영향패널별로 엣지 밴딩이 적용되는 방식과 패널의 엣지 밴드 설정에서 두께가 표시되는 위치를 알아보세요.
- 사전 밀링 및 엣지 밴드에 대해 Cut L 및 Cut W 표시Add the Cut L and Cut W columns so the cutlist shows cutting size alongside finished size.
- 재단 목록에서 재단 치수 및 엣지 밴딩 열을 활성화하여 패널을 확인하세요재단 목록에서 재단 치수 및 엣지 밴딩 열을 켜면 패널 치수가 엣지 밴드 및 프리밀링 설정과 일치하는지 확인할 수 있습니다.
- Get CAM details, cut list and raw material BOQ from a production designProduce CAM details, the cut list and the raw material BOQ together from a production design, scoped and downloaded as you need.
모두 보기 (65)
- How panel sizes include edge band and laminate in the cut listLearn how the Finished Size and Cut Size columns in the production cut list differ, and which size CAM output uses.
- 셔터 패널을 숨겨 몸체만 있는 재단 목록 받기재단 목록을 생성하기 전에 셔터 패널을 숨기면 몸체와 보이는 측면만 출력됩니다.
- Fix panel size discrepancies caused by edge band thicknessMake sure the edge band's actual thickness value is correct, because the software calculates panel size from it rather than from its name.
- Get edge banding quantity from the softwareAdd the exact edge band you use to the setup so the software can give you its quantity.
- Show edge band, panel name and size columnsTurn on the edge band column and read panel name, finished size and cut size in the cutlist.
- 패널에 사용자 지정 라벨을 추가하고 재단 목록에 표시사용자 지정 패널을 포함한 패널에 사용자 지정 라벨을 추가하고, 사용자 지정 라벨 열을 활성화하여 재단 목록과 스티커에 표시되도록 합니다.
- 겹치는 항목에 대해 레이블 속성으로 사용자 지정 레이블 추가레이아웃에서 레이블이 겹칠 때 레이블 속성을 통해 사용자 지정 레이블을 추가하고, 필요한 위치에 배치하세요.
- Choose what prints as the panel name on labelsSet the panel-name element on a label template so the printed label, preview and machine files show the design name, the custom label or a combined name.
- How edgeband lengths in the BOQ are calculatedSee how extensions, edge profiles, pre-milling, cut shapes and wastage adjust each band's BOQ length so you can reconcile the totals.
- How mapped edge band thickness drives cut list dimensionsLearn how the edge band thickness mapped to a material directly affects the cut list dimensions.
- 컷 리스트 패널의 정렬 및 그룹화 방식을 이해합니다생산 컷 리스트가 패널을 캐비닛별로 오름차순으로 나열하는 방식과 각 패널의 방을 확인하는 방법을 알아봅니다.
- Choose the cutlist type and export the cut list CSVSwitch the cutlist type on the Cutlist tab and export a CSV that follows the selected type for beam saw machines.
- 생산 설정에서 절단 목록 열과 치수 정확도 구성필요한 절단 목록 필드를 켜고 치수 정확도를 설정하여 생산 출력이 원하는 방식으로 치수를 반올림하도록 하세요.
- 생산 보기에서 재단 목록 다운로드생산 보기에서 패널 목록을 Excel 또는 PDF 파일로 다운로드하고 해당 열을 확인하십시오.
- Read panel dimensions in the cut size columnFind each panel's dimensions in the cut size column of the cut list.
- Understand cut edgeband on panels with cut or slanted edgesLearn when a panel carries a cut edgeband and why rectangular panels correctly show 'No Edgeband'.
- Generate and download a cut list with cut length and edge bandsGenerate a cut list from the production module and download it, enabling parameters such as cut length and edge bands before generating.
- How cutting size is calculatedLearn how cutting size subtracts edge banding and pre-milling from the panel dimension.
- How shelf depth is calculated in cut listsLearn how an adjustable shelf's depth is derived from the carcass depth, the shelf reveal and the back panel offset.
- Set board sizes, offcuts and saw width in Board Layout SettingsGive each board type its sheet sizes and stock offcuts, set the cutting type and saw width, and override the size for a single board when needed.
- Set pre-milling type and read edgeband columns in the MES cutlistChoose how pre-milling is applied and read each edge's band and cut length in the MES cutlist.
- Understand shutter sizing in a child partitionLearn why a shutter added to a child partition takes its size from that partition rather than the overall unit height.
- Understand skirting notches on wardrobe carcass side panelsLearn which units get skirting cuts on carcass side panels, how each wardrobe type maps its cuts, and what to check when a notch is missing.
- Add Combined Label and room name columnsTurn on the Combined Label and room name columns and move room name to the top of the cutlist.
- Change the cabinet code shown in cutlist outputsEdit the cabinet code field's display name in the Homag or Biesse tab of Cutlist Preferences so your cutlist outputs show the column name you want.
- Check which downloads need a published work orderSee which footer downloads stay disabled on an unpublished work order and which ones remain available.
- How cut dimensions relate to finish dimensionsLearn when a panel's cut length and width match its finish dimensions and when edgebanding makes them differ.
- How cutlist and board layout accuracy settings control decimal placesLearn how the accuracy control in cutlist settings and board layout settings decides how many decimal places sizes are shown with.
- How cut list panel names use unit and panel codesLearn how each cut list panel is identified by a unit code plus a panel number and how that identifier links back to the 3D model.
- How the Room Name field in cutlist labels is filledLearn where the Room Name field in the cutlist/label export gets its value and what it shows when a project has no room defined.
- Identify rooms in the cut list without renaming cabinetsShow the room name as a separate column in the cut list so you can tell which room each cabinet belongs to without changing the cabinet name.
- 작업 범위로 절단 목록을 한 방으로 제한단일 방에 대한 작업 범위를 생성하면 절단 목록에 해당 방의 캐비닛만 반영됩니다.
- Open Cutlist Settings and apply column changesOpen Cutlist Settings from the cutlist header and apply visibility, naming and order changes per cutlist type.
- Review cut list by cabinet then panel detailsOpen a cabinet's cut list, check each panel's details and mark panels verified, and view the unit visually to confirm rails, shelves and back panel position.
- Set pre-milling type by edge-band thickness or for all panelsChoose whether pre-milling follows each panel's edge-band thickness or applies the same setting to all panels, then save and recalculate to verify the cutting length.
- Set the grain convention and show grain in panel infoChoose how grain is labelled and see the Grain row in the board layout's panel info.
- Understand fixed shelf depth and partition dimensionsLearn that the partition refers to the space within the carcass, not the outer panel, when reading fixed shelf depths.
- Add extra custom columns to a cutlist exportLearn how many extra custom columns you can add beyond the standard fields when exporting a cutlist for a third-party saw or ERP system.
- Change a panel's core in QC mode > Panels > Modify PanelsSet a panel's Core Material Source and, when you need a different core for that panel alone, switch the Source to Custom and change it.
- Change the cabinet code label in cutlist preferencesChoose the Cabinet Code field for cutlist output and set its display name on the Homag, Biesse or Basic tab.
- Choose between a full top panel and half railsLearn how a full top panel uses more material and gives different panel sizes than half rails.
- Control cut list columns and their exported orderFilter rows with the search box and set column visibility, names and order so the export matches the screen.
- Create a custom cut list machine format under SettingsSave a machine under Settings so it appears as a custom cut list option.
- Enable material code column to group cutlist by core materialUse the material code column, which carries core material information, to group the cutlist by core material.
- How back panel material assignment affects finish sheet countLearn why a finish can show more sheets than expected when a back panel uses a different material from the carcass.
- How board layout dimension accuracy worksLearn what the board layout dimension accuracy setting under Display settings controls and what it does not change.
- How construction edges change carcass panel sizes in the cutlistLearn how the inset or outset choice at each shared carcass edge changes panel sizes in the cutlist.
- Read part codes and part names in the cut listLearn how the part code and part name in the cut list tell you which cabinet and which panel a row belongs to.
- Remove cut length and cut width columns when pre-milling is usedHide the cut length and cut width columns from the cut list display when pre-milling makes them unnecessary.
- Set cut list preferences for decimals, quotes, info and CNC machineSet the cut list preferences that control decimals, text shown in quotes, additional information and the CNC machine.
- Set dimension accuracy and header options per cutlist typeSet dimension accuracy to 1 mm and switch on project and store header rows for the cutlist type you are working with.
- Set elevation preferences in the admin portalControl which panels appear as additional manufacturing details in elevations by setting the elevation preferences in the admin portal.
- CSV 출력과 선택한 열로 패널 톱 기계 설정절단 패널 톱 기계를 구성하여 부품 코드부터 시작해 필요한 열이 포함된 CSV 절단 목록을 출력하세요.
- Show client name and work order code columns in the cutlistSwitch on the client name and work order code columns in the cutlist field settings so they appear alongside the room name.
- Show material code alone by turning off finish columnsCombine the core material code with the external and internal finish codes into one material code and hide the separate finish columns for a more compact cutlist.
- 기본 재단 목록을 이해하고 유닛의 패널 찾기기본 재단 목록에 표시되는 내용, Operations 및 Quantity 열이 나타나는 시점, 그리고 이 목록에서 유닛의 패널을 검색하는 방법을 알아보세요.
- Understand why PVC skirting is not on the cut listLearn that PVC skirting is bought readymade, so it is never cut from wood and never appears in the cut list.
- Use pre-milling to compensate for edge-band thicknessApply a per-side pre-milling allowance instead of cutting panels oversize, and decide whether your factory needs pre-milling at all.
- 재단 목록에서 사전 밀링 열이 필요한 경우Learn when the pre-milling column in the cut list is required and when it is only useful for panels whose pre-milling setting differs per edge.
절단 목록 출력 및 기계 형식52
- NC 및 빔 소 기계용 Infurnia CSV 절단 목록의 작동 방식NC 또는 빔 소 기계용 Infurnia CSV 파일에 포함되는 내용과 기계에 맡겨지는 부분을 알아보세요.
- Read the machine list and handle unsupported output formatsRead the machine list columns and, when a format is missing, test with a CSV cutlist or confirm the format with the vendor.
- 작업 지시서에서 절단 목록과 원자재 출력물을 다운로드합니다작업 지시서를 게시한 후 생산 포털에서 절단 목록, 원자재 목록, 보드 레이아웃을 다운로드합니다.
- Match each machine Output selection to its file formatSee which file extension each machine Output selection produces, from .mpr and .cix to .nc, .xml and .dxf.
- 재단 목록과 판재 레이아웃을 다운로드한 후 심재 재료별로 정렬하세요게시된 버전에서 재단 목록과 판재 레이아웃 문서를 다운로드한 후, CSV를 심재 재료별로 정렬하여 특정 판재 유형의 재단 목록을 확인하세요.
- 절단 레이아웃, 컷리스트 및 CNC 파일 출력톱과 기계용 보드 레이아웃, 컷리스트 및 CNC 파일을 받으세요.
모두 보기 (52)
- 자재, 하드웨어 및 BOQ 목록 출력조달 및 확인을 위한 자재, 하드웨어, 보드 유형 및 BOQ 목록을 생성합니다.
- Add a machine in MES machine settingsAdd a machine by choosing its type, category and output format, then enter its name and settings.
- 재단 목록 열을 선택하고 패널 일람표 CSV를 내보내기62개 재단 목록 열 중 표시할 열을 선택한 다음, 정보 행과 엣지 밴드 길이를 포함하여 패널 일람표를 CSV로 내보내세요.
- Download profile cutting lists and board-based material listsDownload the Profile Cutting List and the board-based wooden raw material list from their download groups.
- How drill information and the cut list come from hardwareLearn how the hardware you define in the design produces drill information and the cut list.
- Understand what the Raw Materials page shows and where it comes fromSee what the Raw Materials page covers and why its sheet counts depend on the board layout and its violations.
- Download a raw material summary for a completed projectDownload a raw material summary of core, finish and edge band material once the project is complete.
- Explore the Board Layout footer, optimization settings and outputs in MESLearn what the all-board-types footer, Optimization Settings, Exploded View output and Cutlist type dropdown offer in an MES work order.
- Get a screw-level hardware list from production outputSee how production output gives you a basic hardware list, and how configuring hardware setup lets it detail individual items such as which screw is used and how many are required.
- How Material.csv and Sheet.csv are derived in Biesse nesting machine filesLearn what the Material.csv and Sheet.csv master files in a Biesse (CIX) nesting machine zip contain and how their rows and sheet sizes are derived.
- 패널 도면 PDF에서 드릴 위치, 범례 및 선 스타일 읽기수동 패널 도면 PDF가 각 드릴의 위치, 크기 및 유형을 어떻게 표시하는지 알아보아 작업 현장에서 읽을 수 있습니다.
- Add a panel-saw machine to the Custom Cutlist menuRecognise when no panel-saw machine is configured and add one with the right role.
- 기계 출력을 선택하기 전에 허용되는 파일 형식을 확인하세요출력 형식을 선택하기 전에 기계가 허용하는 파일 형식을 확인한 다음, 플랫폼에서 제공하는 호환 출력을 사용해 보세요.
- Check the cut list by downloading summary and board informationDownload the summary and board information to check the cut list.
- Choose the machine and edit its tool parametersPick the machine in the download step to get its post-processor output, and edit a nesting machine's tool parameters in its settings dialog.
- Configure cutlist export options and pre-millingSet dimension accuracy, quotes, header rows and pre-milling values so exported cutlist values come out correct.
- Confirm the format a machine accepts before exportingCheck the machine's supported format before exporting cut list and production data, and plan a CSV workflow when DXF carries geometry only.
- Download a machine-specific cutlist from Custom CutlistPick a panel-saw machine from the Custom Cutlist menu to download the cutlist formatted for that machine.
- Download a PDF of the production layoutDownload a PDF of the production layout from the toolbar in the production layout view.
- Download CNC file as a zip and upload it to the machineDownload the CNC file, extract the zip and upload the extracted file to the CNC machine.
- Download countertop information as an Excel fileDownload the countertop information as an Excel file so you can review it or use it further.
- Download CSV, PDF board layout, panel labels and CNC file from productionDownload the manufacturing output files you need once the cut list is verified and the work order is published.
- Download machine files for a CNC machineDownload the machine files for a CNC machine from its Machine Files download option, and use the menu beside it for DXF output.
- Download optimization XML and label outputsRun optimization to generate an XML file and label outputs, then confirm and download them from the optimization results for downstream machine and production consumption.
- Download project outputs as PDF or XLSGenerate project outputs and download them in either PDF or XLS format, with a single module's output showing panels, hardware, sizes, material and finish.
- Download raw material and hardware requirement sheets separatelyDownload separate requirement sheets for wooden raw materials and hardware raw materials from the production tab.
- Download raw material list as PDF or CSVGet the plan and quantity for each item, then download the raw material list from the MES work order as a PDF or CSV files to hand to the factory team.
- Download saw files, board layouts and panel labelsGet the saw XML, board layout PDFs and panel labels from the published work order.
- Download saw files from the board layoutDownload saw files for the beam saw machine and get one zip with a separate file per board type, so each board can be cut without further splitting.
- Download saw files, nesting files and panel labelsUse the footer menus to download machine-formatted files and numbered labels for the current scope.
- Download the board layout PDF and cut panels on a tabletDownload the board layout PDF from a published work order to hand to the factory as the cutting instruction, then cut and label each panel on a tablet.
- How machine output files drive machine operationLearn which output files machine operation uses and which generic output is available for a project.
- 머신 설정 구성이 작동하는 방식머신 설정을 한 번 구성한 후 모든 향후 작업에 재사용하는 방법을 알아보세요.
- How the Profile Cutting List and Profile 1D Layout are generatedLearn how the Profile Cutting List is generated from the sizes entered for glass shutters with profiles all around, and how the Profile 1D Layout shows each profile piece cut from the stock length and what remains.
- 컷리스트 내보내기 형식을 사용 중인 톱 기계에 맞추기가져온 패널의 치수가 올바르게 유지되도록, 사용 중인 톱 브랜드에서 작동하는 것으로 확인된 컷리스트 파일 형식을 선택하세요.
- Open the raw materials output and download lists as CSV or PDFOpen the raw materials output from the outputs tab and download the material and hardware lists you need.
- Pull latest Tool and CNC settings from AdminRefresh Tool and CNC settings from the Admin portal into the current work order via Settings.
- 불일치를 진단하기 전에 작업 지시서에서 SAW 파일을 새로 다시 다운로드하십시오작업 지시서에서 SAW 파일을 새로 다운로드하여 기계가 이전 내보내기 파일이 아닌 현재 디자인 치수를 읽도록 하십시오.
- 방별 원자재 수량 보기각 방에 대해 별도의 작업 범위를 만들고 Raw Materials 섹션에서 전환하세요.
- Select manual machine type for multi-boring CNC machines in label templateChoose the Manual machine type for a multi-boring machine and set it in the cut list settings.
- Set up production without a beam sawIf your factory has no beam saw machine, the setup is simpler.
- Understand hardware quantities rounded up to whole setsLearn why per-set hardware quantities in the Raw Material list are rounded up and how to check a quantity that looks too high.
- Understand how the file format is fixed per machine recordLearn why the format is fixed per machine record and how to pick a starting output when the exact model is unknown.
- Understand what the Pasting Report PDF showsLearn what the downloadable Pasting Report PDF contains for full-size boards and cut sheets.
- Use KD XML format for cutting filesChoose KD XML as the output format when you generate cutting files for cutting operations.
- 각 생산 팀에 제공할 출력 파일각 생산 팀에 필요한 출력 파일을 제공하세요. 절단에는 XML saw file, 구매에는 panel material 및 hardware PDF, 조립에는 composite cabinet BQ입니다.
보드 배치 및 네스팅69
- 판재 배치도와 원자재 보고서 공유주방 디자인의 판재 배치도와 원자재 보고서를 공유하면 각 판재에 있는 도어와 패널의 수를 세고 누락된 것이 없는지 확인할 수 있습니다.
- 플랫폼이 패널 절단을 위한 생산 보드 레이아웃을 생성하는 방법플랫폼이 현장 팀이 패널 절단 시 따를 수 있는 생산 보드 레이아웃을 생성하는 방식을 확인하세요.
- Enable stacking per work order and set maximum stack heightTurn on stacking for a work order and set how high boards may stack in its board layouts.
- How the Half / Fractional Sheet Split Gap worksLearn what the Half / Fractional Sheet Split Gap measures, its default value, and which utilization modes enable it.
- How board layout counts boards by material and panel typeLearn how board layout counts boards from the materials and panels defined in the catalogue and lists the requirement for each panel type.
- How grain direction affects board layout optimizationDefine grain direction for each finish so panels are placed according to their grain when the board layout is optimized.
모두 보기 (69)
- How grain direction affects sheet count in nestingLearn why a grain or directional finish forces panels to nest in a fixed orientation and how that can raise the number of sheets you need.
- How panels of different colours or finishes are nested on separate boardsLearn how board layout groups panels by material and finish, so units with different colours or laminates are nested on separate boards.
- How the MES board layout reflects the work order snapshotLearn how the MES board layout shows the design state captured when a work order is cut, not later design edits.
- Read the legends and review panel details before productionUse the legends and PDFs to check grain direction, grooving, edge bands and material details before cutting.
- Rotate a panel to fit while respecting grain directionFit a panel that does not match the board layout by rotating it, and override its grain direction when vertical grain would block the rotation.
- Set dimension accuracy and compare fractional-sheet wasteChoose the dimension accuracy for the layout output and use the waste percentage to compare layouts.
- Change board size or blade settings to recalculate board requirementChange the board size or blade settings and the board requirement is recalculated.
- Configure small-part rules and the split marginDecide when a part counts as small, how far it stays from sheet edges, and how wide the split margin is.
- Control sheet ordering, fractional sheets and where settings are editedSet sheet ordering, the minimum free length for fractional sheets, and adjust these options from inside a project.
- Download and share the board layout and board summary PDFsTake the board layout and board summary PDFs from the footer and forward the layout to the factory or a manufacturer.
- Drill into board types and sheets to spot odd panel groupingsOpen a board type and then a single sheet to see exactly which panels sit on it and how big they are.
- Edit a work order board layout after generationChange a work order's board layout by hand after it has been generated instead of keeping it locked to the production design it came from.
- Edit board layout to move panels and rotate with space barReposition panels between boards in Edit Layout, rotate them with the space bar, and re-sync so two sheets fit on one board.
- Fix an oversized panel by splitting itSplit an oversized panel in the design portal so it fits the board and is included in the layout.
- Fix grain-direction rotation refusalsCorrect a wrong-running grain at the panel's grain declaration instead of rotating it on the sheet.
- How board layout groups panels into board typesLearn how a design's board layout groups panels into board types and proposes a least-waste layout.
- How fractional sheet settings split a sheetLearn how fractional sheet settings divide a sheet by a set fraction, such as a 250 mm fraction or a 50/50 split of the length.
- How grain flags on finishes control panel rotation in board layoutLearn how a panel's grain requirement comes from the grain flag on its finish and why a grained panel is not allowed to rotate in board layout.
- How stacking height limits stack count in board layoutLearn how the maximum stacking height setting in board layout / MES output determines how many boards fit in one stack.
- How the board-layout margin worksLearn what the board-layout margin defaults to, when it is applied and where you can change it.
- Inspect, move and discard panels in a design's Board LayoutClick a panel to see its Panel info, drag it to move it on the sheet, and use Discard Changes to put the layout back.
- Mark all panels of a cut sheet as tracked in bulk from board layoutMark every panel on a cut sheet as tracked in one action when the operator has not scanned each panel individually.
- Optimize board layouts for units automaticallyLet the software calculate board layouts and wastage for units such as vanities and wardrobes, with the option to adjust manually.
- Read and edit board layouts in ProductionOpen Production > Board Layout to see each board type's sheets, yield and offcuts, and edit a layout before saving or discarding it.
- Read panel codes and labels on a board layoutEach panel on a board layout carries a panel code and a label, so the operator can paste the correct label on the correct panel after cutting.
- Regenerate board layout after turning off panelsTurn off all panels except the top and shutter panels, then regenerate the board layout so the shutter panels get their own separate layout.
- Set the cutting type and optimisation criteria for board layoutsChoose straight cuts or nesting, then tune recuts, optimisation criteria and stacking for the layout.
- Troubleshoot a stopped cutting job and read sticker codesCheck margins and saw width when a cutting job stops, and see how the sticker material code is built.
- Turn off half sheet mode from settingsSwitch back to full sheet and apply the change to turn off half sheet mode.
- 절단 계산에서 판재 치수와 톱날 두께 이해하기기본적으로 판재 치수가 양쪽에서 10 mm 트리밍을 어떻게 반영하는지, 그리고 절단 계산을 위해 톱날 두께가 어떻게 별도로 입력되는지 알아보세요.
- Bulk edit board size dimensions and quantitiesChange Length, Width, margins, Available Quantity and Force Use for several ticked board sizes at once, while Offcut flags stay per row.
- Check board sizes and optimization details in board layout viewConfirm board sizes and see the number of panels to cut, optimization percentage and sheets required, with board types separated by core, external and internal finish.
- 절단 목록 최적화 목표 선택최소 자재, 최소 처리 시간 또는 균형 중에서 선택한 후 적용하여 최적화된 배치를 생성하세요.
- Choose optimisation and open board layout optionsPick an optimisation type in the Optimization Statistics dialog, then use the board layout options and switch the cutting type to nesting when needed.
- Choose the optimisation criterion per sheet typePick a criterion for each sheet type, or apply one to all with the Overall row, then continue without recomputing.
- Choose the room and download scope for board layout filesOpen the board layout for one room and set the screen level that decides which panels a download covers.
- Clear an oversized panel violationClear an oversized panel violation either by splitting the panel to the available height or by entering the correct board dimensions in the board layout settings.
- Edit board layout to move panels between boardsMove a selected panel from one board to another in the board layout view.
- Enable minimum distance from edge for laminate border allowanceTurn on the minimum distance from edge setting so laminate border allowance is applied around the panel and set the maximum length of the smaller side in the same settings.
- Find grooving details when the board layout lacks themSee where panels' grooves, such as the back panel groove marked BP, are drawn while the board layout lacks grooving details.
- Fix grain-alignment violation by rotating finish 90 degrees at panel levelRotate the finish 90 degrees at panel level so the panel aligns itself to the vertical grain and the violation clears.
- Fix the "Reconfirm Board Layout cut type" warning when downloading nesting filesSee why the warning appears when a straight-cuts board layout is downloaded for nesting and choose how to proceed.
- Force Use makes nesting consume a specified board size firstForce Use on a board size tells the software to use that size first and only move to the next board size once it is used up.
- 블레이드 두께가 트림 여유와 별도로 계산되는 방식블레이드(커프) 두께가 절단 사이에 별도의 여유로 적용되는 방식과 남은 치수가 처리되는 방식을 알아보세요.
- Inspect a composite sheet and keep the board remainderOpen a composite sheet to see its core material and combined pieces, and keep the unused board remainder for other projects.
- Read the Optimization Statistics modal after a comparison runRun the layout with Decide after Comparison and read each sheet type's sheet count, processing time and offcut figures.
- 레이아웃 오류가 있는 시트의 재컷 한도를 1 또는 2로 줄이기패널이 겹치거나 보드 밖으로 나가는 시트는 해당 시트에만 재컷 한도를 낮춰 수정하세요.
- 자투리를 패널로 추가하여 재사용남은 자투리 판재를 패널 또는 코드로 추가하여 이후 프로젝트에서 사용할 수 있습니다.
- Set board sizes, quantities and force useGive each board size its available sheet count and mark the sizes the optimizer must consume.
- 절단 목록 치수를 반올림하려면 치수 정확도를 1 mm로 설정하세요치수 정확도를 1 mm로 설정하면 시스템이 계산된 치수를 정수 밀리미터로 반올림하여 의도한 패널 크기와 일치시킵니다.
- Set margins, blade thickness and saw widthSet the board margins and saw blade allowance so cutting jobs run with the right values.
- Set material thickness with laminate and 0.01 mm accuracyDefine the core material thickness, add the laminate thickness for the final board thickness, and set the required accuracy to 0.01 mm so the system adjusts the stored measurement.
- Show panel and label codes on the board layoutTurn on the Panel Code Annotations and Label Code Annotations switches so each panel's code and label code appear on the board layout.
- Edit Layout에서 선택한 패널을 배치하는 중 시트 전환브레드크럼의 시트 메뉴를 열어 보드 유형의 시트 간을 이동하고, 선택한 패널을 원하는 시트에 배치하세요.
- Understand how board layout identifies partsLearn that board layout identifies parts by annotation codes such as C1 P10 rather than by panel names like left side, right side, drawer or bottom.
- Understand optimization after a material changeLearn what happens to optimization when core or finish materials are changed in a design.
- Understand panel separation and safety distance in board layoutLearn that board layout uses a fixed panel separation value, traditionally based on saw width.
- Understand the straight-cuts warning when downloading nesting filesLearn why the 'Reconfirm Board Layout cut type' warning appears when you download nesting files and what it is asking you to confirm.
- Understand why a single finish yields fewer sheetsSee why using one finish across panels lowers the total sheet count, since panels of the same finish can be combined on the same sheet.
- Understand why board count differs between viewsThe board count depends on the material combinations applied to each unit, so applying correct materials changes the reported board count.
- Understand why cut-list labels and board layouts show different sizesLearn why a cut-list label shows a size with decimals while the board layout shows rounded whole numbers.
- Use Nesting mode to position a sheet around a damaged cornerOpen a board type and sheet in the MES Board Layout and switch the Mode dropdown to Nesting to see the full cutting layout and place the sheet so a damaged corner falls on an area that gets cut away.
- View a board's layout with labelsClick an individual board to see its layout with labels.
패널 라벨 및 스티커35
- How panel labels and QR codes work in productionLearn what panel labels carry and how their QR codes drive CNC file lookup and order tracking.
- 라벨 출력, 접착 보고서 및 분해 조립도작업장에서 사용할 시트 라벨과 패널 라벨, 접착 보고서, 분해 조립도를 인쇄합니다.
- Select the correct machine type when downloading panel labelsChoose the machine type that matches your CNC machine when downloading panel labels so the QR code starts the correct operations.
- Track work order progress by scanning panel label QR codesScan the QR code on a panel label to track a work order's progress through factory stations and mark completion at each scanned stage.
- Add separate QR codes for top and bottom programs on HOMAG CNC labelsGive a HOMAG CNC panel label separate QR codes for the top machining program and the bottom machining program.
- 패널 라벨의 바코드는 선택 사항이며 추적에 사용됩니다패널 라벨의 바코드는 필수가 아니며 추적에 사용되므로, 추적이 필요하지 않을 때는 바코드 영역을 제거하고 라벨 크기를 줄일 수 있습니다.
모두 보기 (35)
- How panel label defaults are setLearn the default panel label size and border the platform uses.
- Make panel labels visible in the design portalPublish the design so its panel labels for the cut list become visible, without opening the cut list.
- Read panel codes to identify carcass and unitPanel identifiers in production output make it easy to see which carcass a panel belongs to and which unit has to be cut, so a specific unit can be picked out quickly during cutting.
- 머신의 패널 라벨 회전 켜기머신별 설정을 활성화하면 해당 머신의 출력에서 패널 라벨이 회전됩니다.
- Add edge band code, final size and material info to production labelsExtend production labels to show the edge band code, final panel size and internal and external material information.
- Choose which box label template a work order printsSet the default box label template for one work order so its labels print in the layout that client or project needs.
- Create a custom label template based on printer and sticker sizeCreate a custom label template, set your sticker size, choose the information fields to print, then update it and set it as default.
- Create, rename, update and default panel and box label templatesManage the org's panel and box label templates, from creating and customising them to setting the org-wide default.
- 패널 라벨을 생산 출력물로 다운로드패널 라벨은 다운로드 가능한 생산 출력물 중 하나로 생성됩니다.
- Enable loading order and premilling-by-side in sticker templateTurn on loading order and premilling by side in the sticker template so the sticker shows which side faces up and the premilling value per edge.
- Filter and report progress per operationCombine station and tracking-status filters and enable show detailed progress to see per-operation completion.
- 박스 라벨에서 누락된 조직 로고 수정라벨을 다시 생성하거나 로고 구성 및 템플릿 레이어를 확인하여 박스 라벨 미리보기와 인쇄된 PDF에 조직 로고가 나타나도록 하세요.
- 조직 로고와 중복 QR이 충돌하는 패널 라벨 수정조직 로고와 중복 패널 QR이 패널 라벨에 함께 인쇄될 수 없는 이유와 라벨 레이아웃 및 내보내기에서 예상되는 결과를 알아보세요.
- 상자를 삭제한 후 번호가 건너뛰는 상자 번호 수정상자를 삭제하면 해당 패널이 미포장 풀로 돌아가며, 이후 주석을 재할당하여 남은 상자의 이름이 순차적으로 변경됩니다.
- Fix labels not produced on the boring machineScan the drill QR code from the cutting-stage label so the boring machine produces its labels.
- Fix user component annotation labels that cannot be changedUser component annotations are auto-labelled, so their labels cannot be edited.
- 패널 라벨을 자동으로 생성하고 인쇄합니다라벨 레이아웃을 설정하고 포함할 패널 데이터를 선택한 다음, 보드 레이아웃 기능에서 라벨을 다운로드하여 인쇄합니다.
- How panel stickers carry a CNC barcode alongside the scan QR codeLearn how the panel sticker can carry a barcode for the CNC machine in addition to the QR code used for scan tracking, and how a setting switches the machine-file field between a barcode and a QR code.
- 시트 레이블 작동 방식전체 시트 순서에서 각 시트에 고유 레이블이 부여되는 방식을 알아보세요.
- 디자인 포털에서 게시한 후 패널 레이블을 표시합니다디자인 포털에서 디자인을 게시하면 패널 레이블이 표시됩니다.
- Read board layout labels in numerical L-number order per sheetClick any sheet in the board layout to see its labels numbered in numerical order with no missing L numbers.
- Read edge band thickness on the panel labelThe panel label prints the edge band thickness as a number on the side of the diagram where that banding applies, so shop-floor staff see it at a glance.
- Read the external and internal finish on a panel labelOpen the panel label to see which side of a panel carries the external finish and which carries the internal finish.
- Save label printing format files to drive for automatic retrievalLabel creation requires cut sizes, finish sizes, operations, edge banding thickness, and panel indicators.
- Scan panel labels to detect the correct CNC filePanel labels include a barcode that a CNC machine scans to detect the correct file for that panel.
- Show edgeband face grooving on panel labelsShow grooving information on panel labels in addition to the board layout view.
- 박스 라벨에 조직 로고를 표시하고 위치 선택박스 라벨 템플릿에서 조직 로고를 켜고 위치를 선택하세요. 어떤 로고가 사용되는지, 페이지별로 어떻게 동작하는지 확인할 수 있습니다.
- Understand offcut management in productionLearn that offcut management is not currently available in production and that labels are generated only for panels accounted for in a project.
- Update the sticker template after changing sticker settingsLearn how the sticker template controls which information appears on the sticker and can be switched on or off per field.
CNC 및 CAM 작업65
- CNC용 패널 컷아웃을 추가하고 작업 유형과 공구를 지정하세요패널 외부 표면에 홈을 만들고 컷 깊이와 작업 유형을 설정하여 CNC 출력에 사용할 수 있게 하세요.
- CAM 출력에서 백패널 홈이 나타나는 시점 이해인셋 백패널이 주변 패널에 홈 작업을 생성하는 방식과, 해당 홈이 CAM/MES 출력에 포함되는지와 그 방식을 결정하는 환경설정 및 기계 설정을 알아봅니다.
- CAM에 포함을 표시하여 CAM 작업 추가: 유형, 깊이 및 공구디자인 피처를 CAM에 포함으로 표시한 다음 절단 유형, 깊이 및 선호 공구를 설정하여 기계로 보냅니다.
- Add grooves or moulding to a panel and set the CAM operationAdd groove or moulding shapes on the external side of a shutter and send their operations to the CNC.
- Cut a curved or arched panel from a final-size panelStart with a panel already at its final dimensions and cut the curve out of it to produce a curved or arched panel.
- CIX 출력에 대한 Biesse Works 호환성 활성화기계 설정에서 Biesse Works 호환성을 켜면 Biesse CNC 기계가 생성된 CIX 출력을 올바르게 읽습니다.
모두 보기 (65)
- Trimming vs pocketing in CAM operationsLearn how trimming removes material across an entire area while pocketing carves a defined space inside a perimeter.
- 출력 다운로드 전에 CNC 기계 유형과 공구 데이터를 구성하십시오드릴링 면으로 기계 유형을 설정하고 라우팅 및 톱 공구를 추가한 다음, 설정을 저장하고 CNC 출력을 다운로드하십시오.
- Force a tool and finish adding a CNC machineMap drill and contour tools via tool_names, then choose CNC and Generic MPR and set the tool direction and machine name.
- Output CNC files for a work orderAdd a machine in the production setup, choose the CNC panel-by-panel operation and download the generic MPR file.
- Set routing line tool position L, R or C for cut alignmentClick a routing line to see the tool position with L, R and C options, specify a preferred tool, and check the panel preview by selecting the machine instead of raw view.
- Create custom cuts in edit panel design and include them in CAMDraw and offset a custom shape on a panel, define it as a cut with a depth, and enable the include in CAM option so the machining reaches the CNC files.
- Create panel pockets via edit panel design and include in CAMAdd a shaped operation such as a shaker-style pocket to a panel and carry it through to the manufacturing output.
- Enable Include in CAM to push panel operations to productionTurn on Include in CAM when adding a panel operation so it reaches production, then choose the operation type, tool and tool number.
- Enter saw tool name, thickness and axis for back-panel groovingAdd a saw tool row in the CNC machine settings so back-panel grooving operations carry the right tool name, thickness and axis.
- 선호 공구 선택이 머신 비트에 매핑되는 방식2D CAM 모드에서 절단에 선택한 선호 공구가 어떤 머신 비트로 수행되는지 결정하는 방법을 알아보세요.
- Set back panel grooving methodChoose whether back panel grooves are cut by sawing or routing.
- Set the preferred router tool for back panel groovesSet the default router tool for the Back Panel Groove operation in a CNC machine's settings, choosing from tools identified by name, diameter and axis.
- 드릴링 파일을 다운로드하려면 설정에서 CNC 기계를 추가하세요드릴링 파일과 DXF를 다운로드하려면 Settings > Machine에서 CNC 기계를 추가하세요.
- Add CNC tools that match the machineEnter every tool the job uses with names and numbers that match the machine so CNC output can be matched and downloaded.
- Check a tool's type in machine settingsLook up the type assigned to each tool in machine settings to see why a routing tool cannot be listed as a sawing tool.
- Configure CNC machine as 5-face process with panel flipEnter only the saw tool details, including the tool name and thickness, in the machine settings.
- 드릴링 면 수에 따라 CNC 기계 유형 구성CNC 기계 설정에서 기계가 드릴링하는 면 수에 맞게 기계 유형을 설정하십시오.
- Create a groove set to cut and include it in CAM for pocketingMachine a pocket on a shutter by creating a groove set, setting it to cut at the required depth and including it in CAM for pocketing.
- 패널에 파라메트릭 포켓과 도그본 컷아웃 생성패널 면에 포켓을 가공하고 파라메트릭으로 크기를 설정하며, 라우팅을 사용하여 도그본 및 수평 컷아웃을 만드세요.
- CAM 설정의 홈 깊이 공차가 절단 목록의 홈 정확도를 제어하는 방법패널의 2D/CAM 보기에 표시되는 홈 깊이에 시스템이 추가한 공차가 포함되는 방식과 이를 구성하는 위치를 알아보세요.
- Include side panel cuts in CAM outputInclude the panel cuts on the sides of a cabinet in the CAM output.
- Machine radius panels and grooving by editing panel constructionEdit the panel design at the construction level and apply the required tools and operations so the application generates the machine instructions automatically.
- Output top and bottom drilling in one CNC fileTurn off the Separate Top Bottom Files setting on a CNC machine so it outputs a single file containing both top and bottom drilling.
- Restrict a panel area from grooving or drilling via clamping obstructionDefine a restricted rectangular area on a panel in the Clamping Obstructions table so the software rotates the panel when a groove or drilling operation falls inside it.
- Set up a CNC machine with its machine type and settingsUse the Add Machine option and fill in the machine type and the settings the setup stores per machine.
- CNC 출력에서 패널이 회전되어 나오는 이유(또는 회전되지 않는 이유)Always Rotate 설정, Maximum Machine Depth, Min Panel Width가 CNC 출력에서 패널 회전 여부를 어떻게 결정하는지, 그리고 드릴링이 반전되거나 잘못된 모서리에 위치할 때 무엇을 확인해야 하는지 알아보세요.
- 2D Panel CAM Mode에서 드릴 추가 및 편집2D Panel CAM Mode에서 패널에 드릴을 추가하고 위치, 단계 및 기계 깊이 설정을 편집합니다.
- Add machines and tool lists in production settingsAdd each machine with its type, then give it a tool list and pick the tool it uses.
- 머신 사이드 톱 공구 목록에 톱날 공구 행 추가톱질 작업이 머신에서 실행될 수 있도록 이름과 날 두께를 포함한 톱날 공구 행을 추가하십시오.
- Back panel grooves cut end-to-end in generated MPR filesLearn how back-panel grooves defined end-to-end in the design carry through to the generated MPR file and match the drawings on the MES portal.
- Check CAM hole depth in panel 2D CAM modeOpen the panel in 2D view and enter CAM mode to verify hole markings such as drawer channel or tandem depths.
- 도면을 다운로드할 때 클램핑 영역 경고 확인작업 지시에 대한 도면 또는 기계 파일을 다운로드하고, 어떤 작업이 제한된 클램핑 영역 안에 있는지 확인하십시오.
- Check how nesting NC Z values follow machine settingsLearn how the Z values in a nesting NC follow the machine's settings, including what happens when a router is too big for a pocket contour.
- Choose a panel cutting strategy for CNC productionUse the panel-by-panel strategy for CNC cutting and avoid the single-step strategy when two panels are involved.
- Configure a CNC nesting machine with tool lists and NC codesCreate a CNC nesting machine with type CNC / Manual Operations, sub type Nesting and output NC.
- Download and check CNC machine files before productionDownload the CNC output from the published work order, load it into the machine and verify it against the machine type.
- Download CNC machine output drawingsDownload drawings from the CNC machine output that show every panel with its machining details, using reference letters A, B, C and D to determine positions and depth.
- Draw the path before exiting to 3D view for the sweep toolDraw the sweep path before you exit to the 3D view, because the sweep cannot be applied without a defined path.
- Enter saw tool name and thickness in machine settingsEnter the saw tool name and thickness into the machine settings portal and save the settings to complete the CNC configuration.
- Find the download buttons on a work order's CNC Machining tabLocate the Drawing and Machine Files buttons on each machine card and know which formats each machine offers.
- CAM 홈 길이 공차를 조정하여 홈이 제대로 절삭되지 않는 문제 해결관리자 CAM 설정에서 홈 길이 공차를 비트 지름의 절반으로 설정하면 생산 파일에서 홈이 올바르게 생성됩니다.
- Fix missing routing or drill tools in CAM outputAdd the referenced tools and refresh the cache so regenerated CAM output includes every tool the job uses.
- Get board layout and direct XML file for CNCFor production, the platform can provide a board layout as well as a direct XML file for CNC.
- CNC 출력 생성 시 도구가 다를 수 있음 경고 처리CNC 출력 생성 시 "tool may be different" 경고가 나타나는 이유와 잘못된 도구가 선택된 경우 도구 매핑 기본 설정을 수정하는 방법을 알아보세요.
- Infurnia의 .nc G-code 제한 사항: R-호, 커터 보정 없음, mm 절대 좌표Infurnia의 작은 G-code 방언의 고정 규칙을 알아보고, .nc 출력이 컨트롤러에서 무엇을 표현할 수 있고 무엇을 표현할 수 없는지 확인하세요.
- How retract height is calculated from maximum safe ZLearn how the retract height written in the nesting file is derived from the maximum safe Z value and the board thickness.
- 스트립 조명 홈 깊이를 설정하고 확인하는 방법스트립 조명 SKU의 홈 깊이가 패널의 홈 가공 여부와 깊이를 어떻게 결정하는지, 그리고 CAM 출력에서 결과를 확인하는 방법을 알아보세요.
- Biesse CIX 파일에서 ORLST 원점이 선택되는 방식Infurnia가 각 패널의 ORLST 베드 원점을 Default Machine Origin 또는 범위 기반 원점 테이블에서 어떻게 선택하는지 알아보세요.
- Import AutoCAD files for complex CNC panel designsBring a complex carved panel design into Infurnia by importing an AutoCAD file inside the edit panel design feature.
- 톱 폭을 기계 블레이드 폭에 맞추십시오작업 지시서의 톱 폭을 절단 기계의 실제 블레이드 폭으로 설정하고 톱 파일을 다시 생성하여 보드 배치가 올바르게 되도록 하십시오.
- 단위 근접성(C1, C2, C3)으로 CNC 파일 이름 지정바코드의 CNC 파일 이름을 지정할 때 C1, C2, C3과 같은 단위 근접성 레이블을 사용하여 프로젝트 전반에서 동일한 이름 지정 개념이 일관되게 유지되도록 하십시오.
- 오버사이즈 Biesse 패널에 대해 원점별 최대 기계 깊이 재정의특정 원점 행에 더 깊은 최대 기계 깊이를 지정하여 오버사이즈 패널이 해당 행에서만 허용되도록 합니다.
- Set onion-skin passes and through-cut ordering in nesting NC programsControl whether through-cuts are machined in one pass or two, and know that they always run last in the program.
- Set Y-axis maximum and map tools before running CNC fileConfirm tool mapping so the CNC file is ready to run.
- 기계가 기본값을 거부하면 다른 MPR 형식을 사용해 보십시오기계가 플랫폼의 MPR을 올바르게 읽지 못하면 다른 지원 MPR 변형을 사용해 보고, 기계 공급업체에서 정상 작동하는 예제 파일을 받으십시오.
- Panel 2D CAM 편집이 제조 출력에 미치는 영향을 이해합니다Panel 2D CAM 모드에서 제조를 위해 추가할 수 있는 항목과 그러한 변경 사항이 3D 설계에 반영되지 않는 이유를 알아봅니다.
- Verify a nesting program with toolpaths and the NC simulatorOpen the nesting view on a single sheet to check raw or post-processed toolpaths, simulate the NC code and spot missing tools.
- CAM 설정에서 필수 필드 오류로 저장이 차단되는 이유CAM 설정 모달이 저장을 허용하기 전에 입력 내용을 검증하는 방식을 알아보세요.
- .nc 파일의 Z 값이 설정된 Safe Z와 일치하지 않는 이유Z Origin Reference 설정과 through-cut clearance가 .nc 파일에 기록되는 Z 값을 어떻게 이동시키는지 확인하여 올바른 파일과 실제 깊이 오류를 구별할 수 있습니다.
재료, 하드웨어 및 연결구49
- How connectors are assigned per scenarioLearn what a scenario is in connector setup and how it decides which connector is applied to a joint.
- Reduce a single panel's length using panel-level extensionShorten one specific panel by setting a negative extension on it at panel level in a construction style.
- Verify a completed design in QC modeOpen QC mode to see the materials, units and panels used in a completed design before verification.
- Add a connector to several units at onceAdd one connector to many units in a single pass by selecting the scenarios that need it in the Scenario view tab.
- Find and replace a material or edge band in QC ModeTrace which units and panels use a SKU and swap it for another across the design.
- Apply full or half overlay to selected scenarios before adding a connectorApply full or half overlay edits across all current scenarios in the design before adding a connector.
모두 보기 (49)
- Change edge bands in bulk from the production sectionChange the edge band on a line item in the production section and the change applies to every instance of that line item at once.
- Create a new construction style and add all reductionsCreate a new construction style or reuse an existing one, then add all the required reductions including the bottom reduction.
- Inspect units and panels in the QC Mode tabsRead the Units and Panels tabs to see annotations, rooms and where each material came from.
- Read a design's Raw Material Lists and Cabinet Composite BOQLearn what each Raw Material Lists tab and the Cabinet Composite BOQ show, and how to compare lists by item name rather than Sno.
- Read a panel's machining and edge-band drawing in 2D Panel CAM ModeOpen a panel's 2D Panel CAM Mode to see its hinge cups, drill and contour legends, edge-band labels and view options.
- Use X-ray mode to verify drilling before publishingSwitch the production view to X-ray mode to check drilling details on a single component or the whole cabinet, then click X-ray again to return to the solid view.
- Automate connector counts with rulesTell the software how to handle connectors for a given connection so connectors are added by rule.
- Change drawer bottom and carcass panel material at panel levelChange the core material of a drawer bottom panel or other drawer carcass panels by editing the material at the individual panel level in the production portal.
- Correct wrong materials and push the change to productionFix excess or wrong material types in the design and re-sync the work order so production picks it up.
- Inspect assemblies with exploded view, X-ray mode and panel hidingShow an exploded view with an adjustable explode percentage, toggle X-ray mode to see through parts, and turn off individual panels to inspect internal structure.
- Manage connectors on ticked scenarios from the Actions menuPick a connector and apply it to the ticked scenarios, and use a connector card's three-dot menu for Publish, Filter for this, Replace and Remove.
- Replace a connector in the connector card in manufacturing settingsUpdate the connector in the connector card within manufacturing settings so production output uses the changed hardware connector, then confirm it appears correctly in the design.
- replace-and-selected 규칙을 사용하여 커넥터 교체한 커넥터 유형을 다른 유형으로 교체하고 교체된 커넥터 수를 확인하십시오.
- Replace unwanted hardware in manufacturing settingsConfigure the correct replacement hardware so the unwanted item no longer appears in the output.
- Review board layout settings on the MES portalReview board layout settings on the MES portal.
- Tell how many of each item is requiredUse the material and hardware summary to see how many of each item a design requires.
- 옷장 구성 설정에서 뒷걸레받이를 끄세요옷장 구성 설정에서 뒷걸레받이를 끄면 절단 목록에 더 이상 표시되지 않습니다.
- Understand the sliding wardrobe shutter system propertyLearn what the shutter system property controls in a sliding wardrobe.
- Verify connector placement and run a collision checkCheck that connectors are placed correctly and run a collision check.
- Visualise cabinet assembly with exploded viewsCreate exploded views to see how a cabinet goes together, then refresh admin settings to update columns and generate the CNC zip for machine upload.
- Visualise multi-finish shutters in the designSee how multi-finish on shutters can be visualised in the design.
- Add a finish condition to a panel glue manufacturing ruleAdd a finish condition to a panel glue manufacturing rule by setting the condition type to finish and choosing the tag operator 'equal to'.
- Add hardware to a box and handle closed-box warningsSelect hardware with an unpacked remainder, enter a valid quantity, and reopen a closed box if the warning appears.
- Add stability rails to wardrobes wider than 900 mmAdd stability rails as an option when a wardrobe is wider than 900 mm.
- Change material for specific panels using filter parametersFilter the panels in the finished materials view so a material change applies only to the units that match your criteria.
- Check and bulk-change core material by filteringFilter the materials view by core material to spot a wrong ply and swap it in bulk.
- Check panel origin and drilling via 2D panel drawingOpen the 2D panel drawing from single-unit CAM mode or from panel section construction in 3D to inspect an operation's connection type, connector card name, hardware SKU name and rule.
- Check where a panel's hardware came fromRead the connector source in the connector scenario view to tell whether a panel's hardware was inserted by a hardware rule or placed by hand.
- Define connector height ranges with an infinity upper boundDefine multiple bands for a connector's height range, including a final band with an infinity upper bound.
- Define custom LED strip sizes in the admin portalDefine any custom LED strip sizes in the admin portal so they are available for LED grooves in CNC output.
- How cabinet and panel annotations identify modules and panelsLearn how unique cabinet and panel annotations identify modules and the panels inside them for board layout.
- Machine files do not output two separate groups for split shuttersWhen a shutter is split into two parts using a divisional shutter, the design and 3D view show two separate panels.
- Reproduce rejected panels using rejection recordsUse the rejection record kept for a rejected panel to reproduce it when remanufacturing.
- 프로덕션 커넥터 및 시나리오를 통해 삭제된 하드웨어 복원프로덕션 디자인에서 디자인을 열고 3D와 커넥터 및 시나리오로 이동한 후, 카탈로그에서 일반 유리와 같은 재질을 다시 지정하여 삭제된 하드웨어를 복원하세요.
- Set dummy panel depth to 0 mm to fix Gola cut on blind unitsSet the dummy panel depth to 0 mm so the Gola cut and shelf reveal on a blind unit come out right.
- Track edge banding, core material and finish in panel schedulesCreate and download panel schedules as CSV to track edge banding, core materials and finishes and spot panels with discrepancies.
- Understand connector counts and drills in Scenario viewLearn why the Connectors column counts connector cards on a scenario and how each card's quantity and offsets set the number of drills.
- Understand the Modular Units Hardware tabSee what the Hardware tab lists for each cabinet, how rows are grouped, and how to check panel drilling details.
- Understand the two hardware lists for procurement and assemblyLearn how the procurement hardware list and the assembly hardware list differ and which one the assembly team should use.
- Use Single Unit CAM Mode with X-ray to verify drillsOpen Single Unit CAM Mode with the shortcut "su enter" and combine it with X-ray to check drill positions and connector details on the 2D panel drawing.
- Verify a cabinet before sending it to productionCheck a cabinet's SKU structure against the rules before you send it to production.
- Work out strip light drivers and screws manuallyPlace strip lights manually in the drawing so the running length is known, then work out the correct driver rating and screw quantities separately.
- Work with connectors and scenarios in single unit CAM modeOpen a cabinet's CAM menu in the production design to reach Single unit CAM Mode (Panel by Panel), Connectors and Scenarios, then manage each scenario of the selected panel.
패널 추적 및 스테이션37
- Open QC Mode and understand its tabs and work scopeEnter QC Mode, see which work scope it opens on, and learn what each of the four tabs shows.
- Track scanned panel progress in a work orderSee the progress of any scanned panel inside a work order, with green ticks for panels scanned at a station and panel-by-panel status within a project.
- Grant MES roles per user and load mapped stationsTurn on MES roles for individual users without admin rights and reload so mapped station data appears.
- Reject and remake a panel from the manual tableReject a panel and remake it, then regenerate the remake's outputs from the Rejections tab.
- Set up stations and operators for panel trackingStart tracking with one person at a chosen station and add stations and operators as work progresses.
- Understand exempt panels at edgebanding and CNC stationsLearn why some panels are not trackable at edgebanding and CNC stations and where they appear.
모두 보기 (37)
- Understand Shipment page tabs and station permissionsLearn how the Shipment page's Loading and Unloading tabs depend on the stations mapped to you and what each view requires before you scan boxes.
- Add missing stations and print panel labelsReview the default stations for a new account, add any missing station from station settings, and print panel labels.
- Check per-panel station status on Order ProgressOpen the Order Progress tab to see each panel turn green as it passes each station.
- Create a custom-named station on a standard typeAdd a station by naming it and choosing one of the existing station types.
- Create MES users and stations with the right roles and typesSet up MES admins, MES operators and stations so tracking access can be assigned correctly.
- Deactivate tracking stations a factory does not scan atDeactivate any tracking station your factory does not want to scan at, and station types with no active station are left out of progress calculations.
- Filter tracking data by station status and download the listNarrow production tracking to panels by station status, then download the filtered list.
- 잘못된 스테이션 유형으로 생성된 스테이션 수정스테이션 유형은 생성 시 고정되며 편집할 수 없으므로, 올바른 유형의 대체 스테이션을 생성하고 작업자를 옮긴 뒤 기존 스테이션을 비활성화하세요.
- Get an alert when a panel has already been scannedScan panels on the mobile app and the system alerts you when the same panel has already been scanned.
- Handle rejected panels: retired codes, remakes and undoLearn how a rejected panel's code is retired, how the panel is remade with a fresh code, and when a rejection can still be undone.
- 시작되지 않음 패널 수가 계산되는 방식생산 추적에서 시작되지 않음 수에 포함되는 패널과 이 수가 변경되는 시점을 알아보세요.
- 생산 포털이 작업장에서 QC를 지원하는 방식생산 포털이 원래 디자인을 변경하지 않고 품질 관리 검사와 기계용 출력을 어떻게 제공하는지 확인하십시오.
- How tracking records and statuses are storedLearn what each scan records, which tracking sources exist, and what item status shows.
- Map users to tracking stations and fix missing usersGive each MES user access to the stations they work at and understand why a user may not appear in the Operators list.
- Pick the station and scan panel labels on the phoneChoose the station on the phone before scanning, and only scan the panel's own label so the code is accepted.
- Pre-mark panels that need no operation in the operations columnScan the panels that genuinely require the operation by QR code after pre-marking the rest in the machine operations column.
- Read tracked-panel counts per stationSee why counts differ between Panel Cutting, Edgebanding and CNC, and what a lower count at a later station means.
- Route projects to a factory or vendorConfigure machines per factory or vendor and route a project to the chosen one.
- Scan a panel QR to track it at a stationPoint the scanner at a valid panel label to mark the panel tracked at the currently selected station.
- Scan panels with a Bluetooth scanner or camera modeUse a slow-typing Bluetooth scanner or switch to camera mode, which shows each scan result as a self-clearing sheet on touch devices.
- Scan panels with a camera or hardware scannerUse the camera-based tracker at each station and know that every scan records its source.
- 관리자 포털과 MES 포털에서 사용자별 접근 권한 설정관리자 포털과 MES 포털 모두에서 권한을 설정하여 각 사용자에게 올바른 접근 수준과 MES 역할을 부여하세요.
- Set up an MES operator for tracking station scanningCreate the MES operator as a user in the admin portal with their email ID and map them to a tracking station before scanning can be used.
- Set up factory-floor tracking from workflow to first scanPlan your stations, create operators, assign them to stations and start scanning on Android devices.
- 추적 스테이션을 삭제하는 대신 끄기Settings > Configure stations에서 추적 스테이션을 끄면 운영자의 스테이션 선택기에서 사라지지만, 추적된 패널은 이력을 유지합니다.
- Track panels manually from the Manual tableOpen the Manual table, pick a published work order and track the panels you need at the station.
- Track panels with a phone camera or the Manual viewUse a phone camera or pick panels in the Manual view when no hardware scanner is at hand.
- Understand station-scan gating and scan orderLearn that gating is all-or-nothing and that scanning out of sequence is not blocked.
- Understand the nine station types and how panels are trackedLearn which station types are scan stages, which are box-based, and how default and extra stations behave as one stage.
- Understand where scan summaries are shownLearn that the platform shows a browser summary of which panel was scanned at which station and at what time.
- QR 스캔이 무시되고 'Scan ignored' 토스트가 표시되는 이유앱이 스캔을 수락하지 않고 'Scan ignored — <reason>' 토스트를 표시하는 이유와 Tracking 및 Shipment 페이지에서 각 이유가 무엇을 의미하는지 알아보세요.
포장 및 배송24
- Create a box manually on the Packaging pageCreate a box manually on the Packaging page so the factory floor gets a packaging list to pack panels and box labels can be printed before packing.
- 박스를 생성하고 라벨을 인쇄한 뒤 포장을 위해 닫으세요생산 인터페이스에서 박스를 생성하고 패널을 추가한 뒤 라벨을 인쇄하고 닫아 재단된 패널을 포장하세요.
- How the Shipment/Order Status counts are derivedLearn how boxes, panels and hardware each count towards shipment progress on the Order Status page.
- 포장 카운터를 확인하고 박스 라벨과 목록을 다운로드하세요Packaging 페이지 헤더에서 포장된 패널과 하드웨어를 추적한 다음 Box Labels, Packaging List, Unpacked Panels를 PDF로 다운로드하세요.
- Read the Shipment Loading view and open the Shipment SummarySee the selected shipment's status, loaded and pending boxes, and the actions available, then open its full Shipment Summary.
- Add panels to a box and print its label on the MES Packaging pageTick panels in the Manual panel selector, confirm adding them to a box, and print the box label to close it.
모두 보기 (24)
- Add panels to a box with the Manual panel selectorFall back to the Manual panel selector to filter panels by core, finishes, edge bands and operations and place them without scanning.
- 화면 오른쪽의 버튼으로 포장 상자를 생성하세요Packaging 페이지에서 작업 지시에 대한 새 상자를 생성한 다음 라벨을 인쇄하고 상자를 닫아 포장을 완료하세요.
- Create a shipment for a work orderOpen the Shipment section for the work order, create the shipment with driver, vehicle, dispatch and receiver details, then scan box labels to mark them loaded.
- 박스 생성, 라벨 스캔 및 발송을 위한 배송 세부 정보 입력포장용 새 박스를 생성하고 모든 패널이 추적되는지 확인한 다음, 박스 라벨을 스캔하고 발송에 필요한 수령인, 운전기사 및 차량 세부 정보를 입력하십시오.
- Enable the packaging page and map operators to a Packaging stationPublish the work order and map each operator to a tracking station of type Packaging so the page is active.
- Fix packaging scans that are ignoredOpen a box and clear the invalid-QR popup so the packaging scan listener accepts your scans.
- Fix "Panel is already in Box" errors and move panels between boxesLearn why a panel can sit in only one box, what the error means, and how to move a panel to a different box.
- Handle invalid codes and duplicate or closed-box scansRead the reason for an invalid code, pick the panel manually, and confirm before adding to a closed box.
- Load and unload boxes on the Shipment pageScan box QR codes to load and unload boxes, use the tabs and unload list, and revert actions without losing track of records.
- 상자 라벨을 스캔하여 배송할 상자를 적재하세요모바일 폰으로 로그인하고 상자 라벨을 스캔하여 배송할 품목을 적재하세요. 아직 적재할 상자와 각 상자의 내용물을 확인할 수 있습니다.
- 박스 라벨을 인쇄하고 박스를 닫거나, 인쇄되지 않은 라벨을 수정합니다Packaging에서 박스 라벨을 인쇄하거나 라벨 없이 박스를 닫고, 라벨이 누락되거나 최신 상태가 아닌 이유를 확인합니다.
- Print labels and close boxes for the project stepDownload the labels and packaging listings, then print each box label and close the box until all boxes are done.
- Print or save the Shipment Summary for the driverOpen the Shipment Summary from the Shipment page and print it directly or save it as a PDF to send to the driver.
- 모바일 앱에서 상자를 스캔하고 배송 요약을 확인하세요상자를 스캔하여 적재 여부를 확인한 다음 모바일 애플리케이션에서 배송 요약을 여세요.
- Track packaging and shipment in order progressUse order progress to track packaging and shipment so you can trace components missing during shipment.
- 프로젝트 포장 목록으로 포장 상태 추적각 프로젝트에 포장 목록을 만들어 시스템에서 아직 포장되지 않은 항목을 표시하도록 하세요.
- Track unpacked hardware while packing boxesUse the unpacked items list and remove hardware to return its quantity to the unpacked pool.
- Undo tracking and acknowledge a Panel Not Required alertUndo a tracking in one click from the success message or acknowledge the Panel Not Required alert.