파티션, 선반 및 내부 구성
가이드: 104
- 칸막이, 선반, 서랍 및 도어를 추가하고 구성합니다칸막이 수준에서 구성 요소를 추가하면 각 선반, 서랍 세트 또는 도어 시스템이 해당 부분에만 적용됩니다.
- Change partition dimension instead of translating a shelfAdjust a cabinet by manipulating partition levels, add a shutter system at the partition level, and avoid translating a shelf so the shelf still matches the partition layout.
- Add shelves 및 파티션, 셔터 시스템을 통한 셔터파티션 옵션으로 선반을 추가하고 Add Shutter System 옵션으로 셔터를 추가한 다음, 메커니즘을 싱글 스윙 또는 더블 스윙으로 설정하세요.
- 파티션 또는 패널 수준에서 선반 노출 조정파티션 수준에서 선반 노출을 변경하거나 패널 수준에서 단일 선반의 앞쪽 가장자리를 이동하여 내부 선반이 간섭을 피하도록 하십시오.
- 고정 높이를 설정하여 파티션 분할을 제어하고 서랍을 추가하세요선반 또는 수직 파티션으로 캐비닛 파티션을 분할하고, 섹션에 고정 높이를 설정하여 크기를 지정한 다음, 행거봉 또는 선반을 추가하세요.
- 외부 도어와 서랍의 선반 노출을 0으로 설정하십시오내부 선반 간격으로 인해 외부 도어와 서랍이 어긋나지 않도록 선반 노출을 0으로 설정하십시오.
- 옷장 선반과 경첩의 노출 간격을 5mm보다 크게 설정옷장 선반과 경첩이 부딪히지 않을 만큼 선반 노출 간격을 충분히 크게 선택한 다음, 경첩 위치와 비교해 확인하세요.
- Add a vertical partition and drawers on either sideChoose which side a vertical partition goes on, then add and configure drawers on each side once the vertical and shelves are in place.
- 파티션에 Add shelves하고 선반 노출값을 0으로 설정하세요선택한 파티션 공간에 Add shelves하고 선반 노출값을 0으로 설정하여 앞쪽에 틈이 없도록 하세요.
- 파티션과 붙박이장 전체에서 선반 노출값 관리선반 노출값이 중첩된 파티션에 어떻게 적용되는지, 여러 붙박이장에 한 번에 적용하는 방법을 알아봅니다.
- 파티션을 분할하고 하위 파티션을 편집파티션 레벨에서 파티션을 추가하여 상위 영역을 분할하고 각 하위 파티션을 개별적으로 편집하세요.
- 옷장에서 분리된 칸막이를 개별적으로 작업하기분할된 옷장의 각 칸막이를 개별적으로 선택하여 한 구역에만 도어를 추가하거나 다른 구역은 그대로 둔 채 선반을 변경할 수 있습니다.
- 캐비닛 구역 내부에 칸막이와 유리를 추가캐비닛 구역 내부의 빈 공간에 칸막이를 추가하여 캐비닛 내부를 균등하게 나눕니다.
- 패널 섹션 구조 설정으로 선반에 프로파일 추가하기필요한 면에 패널 섹션의 구조/상단 설정에서 프로파일을 추가하여 선반에 프로파일을 올리세요.
- Add shelves 및 파티션을 클릭하여 걸이 공간파티션을 클릭하여 옷장 안에 선반과 걸이 공간을 추가하고, 하단의 서랍을 고려하여 배치하세요.
- 셔터 공간에 선반 리빌 20 또는 25를 적용하십시오서랍 세트를 추가하기 전에 선반과 칸막이가 설정되도록 셔터 공간에 선반 리빌 20 또는 25를 적용하십시오.
- 옷장 칸막이, 선반 및 구역 맞춤 설정긴 행거 공간이나 서랍 구성 등 고객의 요구에 맞게 칸막이, 선반 및 구역을 배치하세요.
- 파티션을 고정 높이로 설정하여 높이를 변경하세요파티션을 고정 높이로 전환하고 필요한 높이를 입력하여 파티션 하나를 더 높거나 낮게 만드세요.
- 옷장 환경설정에서 선반 및 칸막이 가장자리 표시 여부 설정Cabinet Preference / Wardrobe Preference에서 고정 선반, 조절 선반 및 수직 칸막이 패널의 전면/몸체 보이는 엣지 밴드를 몸체 비표시로 설정하십시오.
- 선반을 수평으로 맞추려면 선반 노출부와 전면 간격을 0으로 설정하세요선반을 수평으로 맞추려면 왼쪽 패널의 선반/판재 구성 설정에서 선반 노출부와 전면 간격을 편집하세요.
- 파티션과 구성에서 선반 노출 설정파티션의 선반 노출을 설정하거나, 디자인의 노출을 유지하거나, 구성이 상위의 값을 따르도록 하세요.
- 선반을 고정식 또는 조절식으로 설정하고 칸막이의 크기를 지정하세요고정식 또는 조절식 선반을 선택하고, 칸막이 자체에서 칸막이의 너비와 비율을 설정하세요.
- 파티션을 이해하고 캐비닛 내부에 선반, 패널 또는 서랍을 추가하세요Infurnia에서 파티션이 무엇인지 알아보고 파티션 수준에서 선반, 수직 패널 또는 서랍을 추가하세요.
- 선반 또는 칸막이를 삭제할 수 없는 이유선반 또는 칸막이 패널이 삭제로부터 보호될 수 있는 이유와 이를 우회하는 방법을 알아보세요.
- 셔터와 서랍 사이의 선반 정렬셔터와 서랍 사이에서 선반이 기본적으로 어디에 위치하는지, 그리고 익스텐션을 조정하여 정렬을 어떻게 이동하는지 알아보세요.
- 선반을 가변식에서 고정식으로 변경파티션 레벨에서 추가한 선반은 처음에는 가변식이며, 패널 레벨에서 유형을 변경하여 고정식으로 만들 수 있습니다.
- 미리 정의된 칸막이 구성을 선택하세요개별 유닛을 배치하는 대신, 채움판 위치가 요구 사항과 일치하는 미리 만들어진 레이아웃을 선택하세요.
- 선반과 수직 공간을 균등하게 또는 정확한 치수로 분할합니다Add shelves 및 수직 구분은 기본적으로 공간을 균등하게 분할합니다. 또는 공간을 선택하고 정확한 치수를 입력하여 불균등하게 분할할 수 있습니다.
- 기본 선반 리빌 거리의 작동 방식선반 리빌 거리가 기본적으로 어떻게 설정되는지, 카탈로그 항목을 만들 때 이를 왜 기록해야 하는지 알아보세요.
- 파티션 섹션을 고정하고 정확한 높이를 설정하세요파티션 섹션을 고정으로 전환하고 치수를 지정하여 정확한 파티션 높이를 설정하세요.
- 내부 선반을 고정 패널로 만들고 셔터 재질 설정캐비닛의 내부 선반을 고정 패널로 설정하고 앞면에서 20mm 줄입니다.
- Front shift로 파티션과 패턴을 벽에서 앞으로 오프셋하세요벽에서 앞으로 오프셋을 설정하여 파티션, 서까래 및 그려진 패턴이 원하는 거리에 위치하도록 하세요.
- 구조에서 선반을 추가하기 전에 수직 칸막이를 제거하세요수직 칸막이가 있는 자리에 선반을 배치하려면 먼저 칸막이를 제거하고 선반을 추가한 다음 수직 칸막이 단계로 돌아오세요.
- L자형 코너 칸막이를 Front Major 또는 Side Major로 분할L자형 코너 칸막이를 분할하고, 각 구역에 선반을 추가하며, 패널 치수를 정렬합니다.
- Add a partition configuration to a wardrobe with or without shuttersAdd an internal layout to the root partition whether the shutters are still on or have been removed.
- Add a ready-made internal layout to a cabinet partitionGive a client ready-made internal options by adding a pre-made layout to a cabinet partition, then fine-tune individual panels.
- Add a shelf above a shutter by hiding the appliance and using the partitionAdd the shelf at the partition level so it matches the arrangement used in similar units.
- Add base and loft shelves via partition dimensions using clear heightSet the base shelf from clear height and add a second shelf to divide the loft and fix its height from the top partition dimensions.
- Add fixed shelves at partition level using switch to fixedAdd a fixed shelf at a partition level with a specific height by using 'Switch to Fixed Height' on the partition section rather than on the shelf panel.
- Add hanger rod and pull-out rod via partition-level customizationOpen partition-level customization for a wardrobe section and add a hanger rod and pull-out rod to its internals.
- Add partition configuration for double-shutter wardrobes with both-side fillerAdd a partition configuration from partition level under construction for a double-shutter wardrobe, choosing from default configurations such as left-side, right-side and both-side filler.
- Add props at partition level so they move with the cabinetAdd props at partition level so they travel with the cabinet, then fine-tune their position in the furniture layer with X, Y and Z offsets.
- Build the internal layout partition by partitionAdd internals on a partition basis, starting with the element that takes the whole area.
- Control sub-partition ratios explicitlySwitch a partition to auto-adjusted height and turn sub-partition ratio on or off, knowing that clearing ratios needs your consent.
- Delete a parent partition to remove all its child shelves at onceDelete a parent partition and the system removes its top and bottom partitions and their child partitions together.
- Edit cabinet partitions from the bottom so the top partition auto-adjustsEdit the lower cabinet partitions and let the remaining height be calculated automatically for the top partition.
- Find the sizing and shelf limits of an L-corner unitOpen an L-corner unit's Customize > Rules to see its Sizing Rules and Shelf Restriction tabs, where Available Space holds Min and Max depth, width and height.
- 칸막이 구획이 자동으로 크기 조정되고 잠기는 방식자동 구획과 고정 구획이 공간을 어떻게 나누어 가지는지, 그리고 왜 한 구획은 항상 자동 조정 상태로 남는지 확인하세요.
- Inset a shelf from left and right using construction offsetsMake a shelf shorter than the full carcass width by entering negative left and right construction offsets.
- 저장된 파티션 구성을 파티션에 불러오기파티션에서 'Partition Configuration' 드롭다운을 열고 저장된 구성을 적용하되, 해당 구획에 맞는지 확인하십시오.
- Place a single vertical partition at the centre of a unitAdd one vertical panel to a unit and it positions at the centre automatically, then adjust the distance manually if the placement is slightly off.
- Read a previously set loft height from the top partition's parent partitionRecover a forgotten loft height by opening the top partition of the reference wardrobe and checking its parent partition.
- Remove a shelf from a designSelect the shelf, open its panel-level menu and use the "Delete Shelf" entry, which is greyed out when the shelf is protected by the disallow-deletion setting.
- Set custom partition sizes using fixed width or fixed heightGive a partition its own size by switching it from equal division to a fixed width or fixed height and entering the value you need.
- Set default shelf count and height limits via designer input rulesDefine designer input rules in preferences and settings so cabinet heights are checked against a min and max range automatically.
- Set partition width and height using internal-to-internal measurementSet a wardrobe partition's width or height by its internal-to-internal measurement so you control the clear opening between panels.
- Set shelf reveal and back panel grooving values as presetsConfigure shelf reveal and back panel grooving values as presets in your account so you do not have to change them repeatedly for each design.
- Set sub-partition ratio on the immediate parent to equalise childrenGive child partitions equal heights by setting the sub-partition ratio on their immediate parent partition.
- Set the partition offset distance inside a carcassLearn what the partition offset value means when you add a partition inside a carcass, so you inset the partition by a distance instead of setting its thickness.
- 기본적으로 스켈레톤 보기에서 선반 주석이 표시됩니다선반 주석은 기본적으로 스켈레톤 보기에서 조절식, 고정식 및 유리 선반을 표시하며, LHS 속성 패널에서 끌 수 있습니다.
- Shelves and partitions do not accept negative sizing valuesShelves and partitions in the design module cannot be given negative sizing values.
- Understand fixed and adjustable shelf dimensionsSee how a fixed shelf runs end to end while an adjustable shelf is reduced on both sides.
- Understand how parent partition numbers are assignedLearn why parent partition numbering in a wardrobe shifts depending on which partition or shelf you click.
- Understand partition selection levels in a cabinetSee how clicking a partition highlights the clicked part and its parent level so you can tell which level of the cabinet you selected.
- Understand the fixed main partition in a rolling shutter moduleLearn that a rolling shutter module's main partition is fixed and cannot be adjusted through the reduction parameters.
- Understand what a wardrobe partition isLearn how the empty internal space of a wardrobe carcass is divided into parts and what the blue area represents.
- Use an invisible shelf to adjust partition height for drawersAdd a shelf, hide it, and use it to set partition height for drawer systems without a physical shelf.
- Add a drawer to a cabinet via partition level and drawer setInsert a drawer inside a cabinet from its partition level, then set its heights and add a shelf below if needed.
- 전체 캐비닛 또는 단일 칸막이에 셔터 시스템 추가개방형 캐비닛 전체 또는 칸막이 하나에만 셔터 시스템을 추가합니다.
- 셔터를 제거하고 선반 영역을 추가하여 외부 옷장 서랍 만들기기존 셔터를 제거하고 선반 영역을 추가하면 옷장에 외부 서랍을 만들 수 있습니다.
- 칸막이, 선반, 서랍 시스템으로 붙박이장 내부를 구성하세요붙박이장의 칸막이 안에 Add shelves, 서랍 시스템, 구성 옵션을 배치하여 내부를 구성하세요.
- 파티션에 셔터 추가파티션에 전용 셔터를 지정하고 단일 셔터, 양문 스윙 또는 리프트업 중에서 선택하세요.
- Add Shutter System을(를) 통해 단일 칸막이에 도어를 추가합니다캐비닛의 칸막이 하나에만 도어를 배치하려면 해당 칸막이를 선택하고 옵션에서 Add Shutter System을(를) 선택합니다.
- Add drawers에서 실행 취소가 아니라 파티션을 선택하여 수행합니다각 서랍이 놓일 파티션을 선택하고 수량을 입력하여 유닛에 하나 이상의 서랍을 추가하세요.
- 셔터를 패널 및 파티션과 정렬가장자리별 축소값을 조정하여 셔터가 돌출 없이 맞닿게 하고, 전체 높이를 유지하거나 파티션을 가리지 않게 하세요.
- 수직 칸막이로 수납장 공간 나누기Add vertical partitions을 사용하여 공간을 나누고 비율 또는 직접 입력한 값으로 너비를 설정합니다.
- 서랍 시스템 컨트롤을 통해 파티션에 서랍을 추가하거나 제거합니다Add drawers to a partition from the partition section and remove them from the drawer system, while also adding shelves or vertical partitions.
- Plan drawers, shutters and partitions before buildingSet shelf reveal, partition heights and shutter or drawer zones before customizing the internals.
- 공간 파티션의 선반에 서랍을 부착하여 서랍 추가하기필요한 높이에 선반을 먼저 추가한 다음, 공간 파티션에서 그 선반에 서랍을 부착하여 칸 안에 서랍을 배치하세요.
- 파티션의 빠른 접근 메뉴에서 서랍 세트 추가파티션에 외부 또는 내부 서랍을 추가하고 LHS와 RHS 서랍 세트를 올바르게 나란히 배치하세요.
- 수직 칸막이를 사용해 나란히 배치된 서랍 추가서랍 사이에 수직 칸막이 하나를 배치하고 서랍 높이에 맞게 크기를 조정하여 나란히 배치된 서랍을 만드세요.
- 파티션에 슬라이딩 및 표준 셔터 메커니즘 적용올바른 파티션에 셔터 시스템을 추가하고 해당 파티션에서 허용되는 메커니즘을 선택하세요.
- 셔터를 추가하기 전에 옷장을 주요 칸막이로 나누세요먼저 옷장을 주요 칸막이로 나눈 다음, 선반과 수직재를 위해 세분화하고, 마지막으로 맞춤형 메커니즘을 갖춘 셔터 시스템을 추가하세요.
- 파티션에서 제거된 셔터 시스템 복원셔터가 제거된 파티션에 스윙 셔터 시스템을 다시 추가하거나, None으로 다시 제거합니다.
- 입면 설정에서 셔터 방향, 유닛 및 선반 주석 표시/숨기기입면 설정에서 셔터 방향, 유닛 주석 및 선반 주석을 켜거나 꺼서 표시되는 입면 주석을 제어합니다.
- 위반 목록에서 경첩 및 선반 충돌 자동 해결위반 검사에서 고정 선반과 같은 위치에 배치된 경첩과 같은 충돌이 보고되면 자동 해결 옵션을 사용하십시오.
- 힌지-선반 충돌 감지를 위한 힌지 치수 구성힌지-선반 충돌을 감지할 수 있도록 모든 힌지 유형의 치수를 개별적으로 구성하세요.
- 음수 오프셋으로 칸막이 치수를 조정하여 서랍 앞판 높이를 설정하세요.음수 오프셋으로 서랍 앞판 높이를 설정할 때 표시되는 칸막이 높이가 전체 높이에서 패널 두께를 뺀 값임을 확인하세요.
- 캐비닛 패널 자체의 레벨에서 마감재와 선반 옵션 설정캐비닛 패널 자체의 레벨을 열어 외부 및 내부 마감재의 출처를 선택하고, 해당 패널에만 적용할 사용자 지정 마감재를 고르고, 선반의 유형과 표시 여부를 설정하십시오.
- 선택 트리를 사용하여 캐비닛, 파티션, 셔터 및 패널 컨트롤에 접근하세요캐비닛 부품을 선택하면 상위 레벨이 표시되며 필요한 컨트롤로 바로 이동할 수 있습니다.
- 수직 칸막이를 사용하여 나란히 배치된 서랍을 수동으로 만드세요선반과 수직 칸막이를 추가한 다음 각 측면에 서랍을 배치하여 나란히 배치된 서랍을 만드세요.
- 스켈레톤 모드로 내부 수납장 칸막이 치수 기입스켈레톤 모드를 켜서 내부 칸막이 치수를 추가하거나, 대신 칸막이 치수를 수동으로 기입하세요.
- 칸막이 높이, 깊이 및 선반 노출을 사용하여 칸막이 패널 배치사용자 지정 패널을 추가하고 회전한 뒤 좌우 치수와 X 및 Y 위치를 설정하여 가로 칸막이 패널을 배치합니다.
- 캐비닛 또는 파티션에 외부 및 내부 한계에 대한 사이징 규칙 설정유닛의 한계가 외부 치수에 적용되는지 내부 여유 공간에 적용되는지 선택하고, 한 번에 하나의 유닛에 적용하거나 일괄 적용하십시오.
- construction 기본 partition 설정으로 cabinet 뒷 panel 분할하기cabinet을 선택하고 construction 기본 partition 옵션을 사용하여 뒷 panel을 분할하거나 수직 divider를 추가하십시오.
- Split top and bottom panels 세로 칸막이당캐비닛의 상판과 하판을 세로 구획마다 한 조각씩 나누어, 각 조각이 해당 구획의 너비를 따르고 양 끝 조각은 옆판 위로 자동으로 연장되도록 합니다.
- Add props to cabinets via partition-level customizationAdd bags, suitcases, storage boxes and other props to a cabinet by customizing a partition.
- Adjust panel front thickness at shelf or individual panel levelSet shelf and panel reveals in millimetres to position shelves and panels precisely from the carcass front.
- Filter panels by type to bulk-select shelves and partitionsFilter the panels list by unit SK name and panel type so you can select many shelves or partitions at once and change their finish in one action.
- Find wardrobe modules in partition internals on the admin portalLocate the wardrobe modules that are available under partition internals in the admin portal.
- How wardrobe internals sit under the parent partitionLearn how the parent partition sits at the top of a wardrobe and holds every sub-partition, shelf, drawer system and other internal beneath it in the hierarchy.
- Set a shelf panel to the Adjustable shelf type with a glass coreSet a shelf panel to the Adjustable shelf type and give it a glass core material such as a tinted glass of a given thickness.