이동, 복사, 대칭 및 배열
가이드: 28
- 패널을 목표 깊이까지 또는 뒤쪽까지 연장목표 전체 깊이에 도달하도록 올바른 연장 값을 입력하거나 패널을 수납장 뒤쪽까지 연장하십시오.
- 캐비닛을 복사하여 붙여넣으면 유사한 캐비닛을 빠르게 만들 수 있습니다먼저 캐비닛 하나를 완전히 조정한 다음 복사하여 붙여넣으면 각 캐비닛을 개별적으로 조정하는 것보다 더 빠르게 여러 개의 유사한 캐비닛을 만들 수 있습니다.
- 걸레받이 대신 패널을 바닥까지 연장하기구성 설정의 연장 매개변수를 사용하면 걸레받이가 보이는 대신 패널이 바닥까지 이어지게 할 수 있습니다.
- construction 탭을 사용하여 panel 확장하기construction 탭에 확장 값을 입력하여 panel의 왼쪽, 오른쪽, 앞 또는 뒤쪽을 늘립니다.
- 확장 매개변수로 패널 모서리를 늘리거나 줄입니다네 방향 확장 필드를 사용하여 패널 모서리를 늘리거나 줄입니다. 음수 값도 사용할 수 있습니다.
- Construction 수준에서 뒷판을 확장합니다뒷판을 확장하려면 Construction 수준으로 이동합니다.
- 경로와 프로파일을 사용한 스윕으로 패턴 트림 만들기트림 윤곽을 경로로 그린 다음, 그 경로를 따라 프로파일 형상을 스윕하여 패턴 트림이나 몰딩을 만듭니다.
- Extrude와 Cut으로 셔터에 트림 및 홈 디자인 만들기그린 영역을 Extrude로 앞으로 당기거나 컷 깊이만큼 함몰시켜 셔터에 트림 및 홈 스타일 디자인을 만듭니다.
- Extend a cabinet end panel to the floor or ceilingExtend an end panel added from a cabinet's End Panel section downward to the floor or upward from its own panel using the Width Extension values.
- R 핸들을 사용하여 패널 측면을 연장합니다R 핸들을 사용하여 패널을 100 mm와 같이 지정된 양만큼 연장합니다.
- 걸레받이가 끊기는 틈을 덮도록 하부 패널을 연장하세요패널을 선택하고, 별도의 걸레받이가 끊기게 될 틈을 덮도록 연장하세요.
- 정확한 거리는 드래그 대신 이동 도구(MV)를 사용하세요드래그 대신 이동 도구를 사용하면 객체를 정확한 거리만큼 이동할 수 있습니다.
- Ctrl+C와 Ctrl+V로 플랫 간에 요소를 복사하여 붙여넣으십시오후드 덕트와 같은 요소를 다시 가져오거나 다시 정렬할 필요 없이 두 번째 플랫에서 재사용하십시오.
- Edit panel design을 사용하여 측면 패널을 경사진 상판에 맞게 다듬기Edit panel design 또는 Edit shape을 사용하여 측면 패널을 사용자 지정 경사 상판 패널의 각도에 맞게 조정하세요.
- Copy and paste a unit with Ctrl+C and Ctrl+VCopy a unit and paste as many copies as you need, with the quotation/costing line generated automatically for each copy.
- Ctrl+C와 Ctrl+V로 요소 복사 및 붙여넣기Ctrl+C와 Ctrl+V 단축키로 요소를 복사하여 붙여넣은 다음, 벽에 문과 창을 배치하세요.
- Copy-paste places repeated copies until Escape is pressedDuplicate a placed unit with Ctrl+C and Ctrl+V, then keep clicking to place as many identical copies as you need.
- Extend a wardrobe beyond 900 mmRemove the width cap so a wardrobe or cabinet can be widened past a fixed limit such as 900 mm.
- Find the Rotate tool and what it doesLocate the Rotate control and use it to turn an object around an axis.
- Trim an extra wall or room-divider segmentRemove an extra wall or room-divider segment using the trim shortcut T R or the trim option in the on-screen menu.
- Furnish와 이동 도구를 사용하여 로프트 유닛을 배치하고 이동하세요Kitchen Furniture에서 로프트 유닛을 배치하고, 화살표 옵션이나 이동 도구로 이동하며, 필요에 따라 박스 로프트를 추가하거나 크기를 조정하세요.
- Place units by dragging or with the move toolPlace a unit in front of the carcass by dragging it or by using the move (MV) tool once the carcass dimensions are correct.
- Set carcass panel thickness and extend fillers to match itMatch your fillers to the 18 mm carcass panel thickness so they line up flush with the carcass.
다른 가이드 5
모두 보기 (5)
- 생산 및 가격 책정에 영향을 주는 구조 옵션 변경몸통 패널의 연장, 연결 및 레일 방식을 조정하면 구조 탭의 변경 사항이 생산 출력과 가격 책정에 반영됩니다.
- 복사는 하나의 사본을 만들고, 곱하기는 반복되는 사본을 만듭니다복사 도구의 복사 옵션과 곱하기 옵션이 어떻게 다른지 알아보고, 도형을 한 번 복제하거나 일정한 간격으로 반복하는 방법을 익히세요.
- Copy objects with the multiply optionPlace a fixed number of copies of an object using the multiply option of the copy tool.
- Repeat profiles with automatic parameter calculationUse the repeater tool in Edit Panel Design to copy and array profiles while the spacing and end point parameters update automatically with the panel size.
- Round shape corners using the fillet radius optionCurve a corner of a drawn shape by setting the Fillet Tool's edge length reduction and applying it to two adjoining edges.