몸체, 걸레받이 및 마감 패널
가이드: 112
- 캐커스, 측면 패널, 엣지 밴드 마감을 셔터에 맞추기캐커스와 측면 패널 마감을 각각 설정하고, 엣지 밴드가 셔터의 보이는 엣지 밴드 설정을 따르도록 하세요.
- 뒷판 오프셋의 측정 및 설정 방법뒷판 오프셋을 어디에서 설정하는지, 캐비닛 외부에서 어떻게 측정하는지, 그리고 뒷판 뒤에 특정한 빈 공간을 남기는 방법을 알아봅니다.
- 유닛에 걸레받이를 추가하고 오른쪽 면에 표시하기비목재 걸레받이를 켜고, 몸통 높이를 올바르게 설정하고, 면별로 걸레받이 표시를 활성화하세요.
- 몸통 외부에 셔터 속성을 적용하는 엔드 패널 추가캐비닛에 엔드 패널을 추가하여, 보이는 마감 측면 패널이 셔터의 속성으로 몸통 외부에 위치하도록 합니다.
- 패널 레벨에서 패널을 편집하여 뒷판 두께 변경아일랜드 주방의 경우 18mm처럼 뒷판에 더 두꺼운 몸체 두께를 적용하려면, 패널 레벨에서 해당 단일 패널을 편집하십시오.
- 뒷판 홈 오프셋과 연장이 구성되는 방식홈이 파인 뒷판의 판재 가장자리로부터의 오프셋과 연장 깊이가 어떻게 정의되는지, 어디에서 설정하는지 알아봅니다.
- 유닛의 걸레받이 유형 및 높이 설정유닛별로 목재 또는 비목재 걸레받이를 선택하고, 제작 옵션에서 걸레받이 높이를 설정하세요.
- 캐비닛 설정에서 캐비닛 걸레받이를 구성하세요캐비닛 구성에서 캐비닛 걸레받이 옵션을 찾으세요.
- Construction 탭에서 걸레받이, 몸통 패널 및 오프셋 구성하기Construction 탭에서 걸레받이, 몸통 패널 및 뒷판 오프셋이 표시되는 방식을 설정하여 캐비닛의 제조 출력이 디자인과 일치하도록 하세요.
- 한 캐비닛의 몸체 마감 변경캐비닛 수준에서 몸체 마감을 변경하면 선택한 캐비닛의 모든 몸체 패널이 함께 업데이트되며, 같은 종류의 다른 캐비닛에는 영향을 주지 않습니다.
- 기본 뒷판 홈 파기를 5mm로 설정기본 뒷판 홈 파기를 5mm로 설정하면 뒷판이 기본적으로 해당 깊이로 홈 파기됩니다.
- 뒷판 확장이 10mm 오프셋을 사용하는 방식뒷판 확장이 10mm 오프셋으로 구성되는 방식을 알아보세요.
- 주방 캐비닛 걸레받이가 전체 유닛 높이에 미치는 영향주방 캐비닛의 약 100mm 걸레받이가 치수에 표시된 몸체 높이에 더해져 전체 유닛 높이가 되는 방법을 알아보세요.
- 측판 또는 측면 걸레받이 사이에 삽입되는 뒷면 걸레받이뒷면 걸레받이가 측판 또는 측면 걸레받이 사이에 삽입되도록 추가하여, 측판이 걸레받이 끝단을 마감하도록 합니다.
- 유닛에서 걸레받이 제거Skirting Visibility 아래의 전면 걸레받이를 꺼서 유닛 앞면에 걸레받이가 더 이상 표시되지 않게 합니다.
- 하드웨어를 변경하여 걸레받이 높이 변경고정 높이 PVC 걸레받이 하드웨어를 교체하여 유닛의 걸레받이 높이를 변경하세요. 일반적으로 100 mm 또는 150 mm입니다.
- 자동 7mm 뒷판 홈 이해하기뒷판 홈은 항상 7mm이며 수동으로 변경하지 않아도 디자인에 올바르게 적용됩니다.
- 벽 섹션과 검색을 통해 벽에 걸레받이 추가내부 벽에 벽 걸레받이를 켜고 검색으로 원하는 걸레받이 베이스를 찾으세요.
- 벽에 걸레받이 추가벽을 선택하고 wall skirting을 켜서 걸레받이를 추가하세요.
- 벽 섹션의 속성 패널에서 벽 걸레받이를 적용합니다벽 섹션의 속성 패널에서 Wall Skirting을(를) 켜고 벽에 적용할 걸레받이 마감을 선택하세요.
- 셔터와 별도로 스커팅 마감 변경스커팅 옷장의 스커팅에 셔터의 기본값 대신 자체 마감을 지정합니다.
- 걸레받이 높이를 수정하면 패널이 자동으로 조정되도록 설정걸레받이 높이 값을 변경하면 전체 높이가 다시 적용되어 수동 편집 없이 패널이 조정됩니다.
- 뒷판 심재를 몸통 심재에 연결캐비닛 환경설정에서 각 뒷판 심재를 이에 맞는 몸통 심재에 연결하면 모든 캐비닛에 뒷판 심재가 기본으로 적용됩니다.
- Resize cabinet end panel at design panel level, not admin portalChange a cabinet end panel's depth in the design phase at the panel level so the change applies only to the cabinet you are working on.
- Set recessed skirting using depth offset in skirting optionsRecess the skirting from the front shutter by entering a depth offset value in the skirting options.
- 몸통 패널을 레일로 변환하고 레일 깊이 설정상판이나 뒷판 등 선택한 몸통 패널을 레일로 변환하고 해당 레일의 깊이를 조정합니다.
- 연결된 뒷판 코어와 라미네이트 두께가 몸통 패널에 미치는 영향연결된 뒷판 코어가 캐비닛의 Carcass Back Core Material을(를) 어떻게 재정의하는지, 그리고 코어와 라미네이트가 패널 두께를 어떻게 정하는지 알아보세요.
- 뒷판 재질을 설정하고 변경하는 방법뒷판 재질이 기본적으로 6mm 표준 보드로 설정되는 방식과 다른 두께나 재질이 필요할 때 변경하는 방법을 알아보세요.
- 옷장 뒷판 홈파기가 구성 설정을 따르는 방식옷장 SKU와 디자인 환경설정의 뒷판 확장 값이 뒷판이 주변 판재 안으로 얼마나 들어가는지를 어떻게 정하는지 알아봅니다.
- 걸레받이 패널의 뒤쪽 익스텐션을 음수로 적용하여 걸레받이 크기 줄이기패널 편집기에서 익스텐션을 음수로 적용하여 걸레받이 구간을 줄이고 걸레받이 주위에 측면 패널을 맞춥니다.
- Set end panel depth to carcass level for open unitsStop the end panel at carcass level on a top unit that has no shutter so it aligns with the carcass.
- 다른 판재 위에 또는 사이에 놓이는 몸통 판재를 설정합니다두 몸통 판재가 만나는 각 모서리에 대해 인셋/아웃셋 구조를 선택하면 두 판재 모두 판재 두께 하나만큼 크기가 조정됩니다.
- 시나리오가 몸통 패널과 접합 패널을 나열하는 방식 이해하기시나리오가 몸통 패널을 먼저, 접합하는 패널을 두 번째로 이름 붙이고 접합하는 쪽을 면으로 표시하는 방식을 알아보세요.
- 걸레받이와 펠멧 옵션이 하부장 또는 벽장 유닛에 따라 달라지는 이유장의 장착 면이 어떻게 해당 장을 하부장 또는 벽장 유닛으로 정하는지, 그리고 그에 따라 어떤 걸레받이, 펠멧, 코니스, 레일 옵션을 사용할 수 있는지 알아보세요.
- 캐비닛 구조에서 엔드 패널 추가 또는 제거선택한 유닛의 캐비닛 구조 설정에서 왼쪽 또는 오른쪽 엔드 패널을 추가하거나 제거합니다.
- 붙박이장 구성에서 걸레받이 높이와 도어 시스템 조정붙박이장 구성 옵션의 세 번째 탭에서 붙박이장과 표준 수납장의 걸레받이 높이 또는 도어 시스템을 변경할 수 있습니다.
- 전체 캐비닛 너비에서 몸체 너비 계산전체 캐비닛 너비에서 몸체 패널 두께의 두 배를 빼서 몸체 너비를 계산합니다.
- 패널 레벨에서 걸레받이의 엣지 밴딩 변경패널 레벨에서 변경하여 걸레받이 영역에 셔터와 다른 고유한 엣지 밴딩을 지정하세요.
- 몸통 외부 마감과 내부 마감 선택캐비닛을 선택한 뒤 캐비닛의 속성 패널에서 각각의 재질 선택기로 몸통 외부 마감과 몸통 내부 마감을 선택하세요. 내부 선택기는 내부 색상을 설정합니다.
- Construction 탭에서 엔드 패널을 업라이트로 변환Construction 탭에서 엔드 패널 자체의 패널을 업라이트로 변환하면, 제자리에 유지되고 업라이트처럼 선반 연결 세트와 드릴 구멍이 생깁니다.
- 카카스 패널의 코어가 선택되는 방식카카스 패널의 코어가 어디에서 오는지, 그리고 패널이 언제 자체 보드를 유지하는지 알아보세요.
- 몸통 연결철물이 자동으로 식별되고 조정되는 방식캐비닛 소프트웨어가 몸통 연결철물을 자동으로 식별하고, 패널 변수가 변경될 때 연결철물의 위치와 수량을 조정하는 방법을 알아보십시오.
- 16mm HDMR 몸통의 뒷판 재료가 선택되는 방식캐비닛 몸통을 16mm HDMR로 설정하면 6mm HDMR 뒷판이 자동으로 적용되는 방식을 알아보세요.
- 붙박이장의 걸레받이 옵션 설정Skirting Options에서 붙박이장 유닛의 걸레받이를 설정하며, 어떤 널을 표시할지와 걸레받이 높이를 선택합니다.
- 캐비닛을 배치하기 전에 몸통 코어와 뒷판 소재 기본값을 설정하세요캐비닛 수준 환경설정에서 몸통 코어와 뒷판 코어 소재를 선택하면 새 캐비닛이 해당 소재로 추가됩니다.
- construction 기본 partition 설정으로 cabinet 뒷 panel 분할하기cabinet을 선택하고 construction 기본 partition 옵션을 사용하여 뒷 panel을 분할하거나 수직 divider를 추가하십시오.
- 엔드 패널과 사이드 패널을 별도의 패널 유형으로 이해하기캐비닛의 사이드 패널과 엔드 패널이 각자의 확장 설정을 가진 별개의 패널 유형임을 알아보세요.
- 몸통 패널 두께 수식을 사용하여 내부 치수를 자동으로 조정수동으로 계산한 내부 치수 대신 몸통 패널 두께를 기준으로 Enter a formula하고, 시스템이 내부 공간을 올바른 값으로 조정하도록 하십시오.
- Add a custom end panel to a cabinetAdd a custom end panel to a cabinet and it extends on whichever side you add it.
- Add a shell and verticals to an empty wardrobe carcassAdd a shell and verticals to an empty wardrobe carcass, then find the partition options in the selection tree on the left-hand side.
- Sweep Tool로 코니스, 몰딩 및 벽 패널을 추가하세요벽에 Sweep Tool을 사용하여 사용자 지정 코니스, 몰딩 및 장식용 벽 패널을 추가하고, 타일 절단의 스윕 모드를 사용하여 벽 몰딩과 셔터 디자인을 만드세요.
- Add or change a back panel on an appliance unitAppliance units come with an open back by default so heat can radiate, and you can add or change a closed or coloured back panel in the open part of the construction.
- Add skirting and extra end panels from cabinet constructionConfigure skirting on a unit and add an extra left or right end panel from the cabinet's Construction tab.
- Apply skirting visibility to new unitsTurn on the skirting visibility preference so the front, left, right and back skirting show/hide state is applied to each unit when it is added.
- Bulk edit drawer carcass thickness and set defaultSet the drawer carcass thickness for all drawers at once, knowing individual drawers can still be overridden later if a different thickness is needed.
- Change carcass sizes to update manufacturing outputsChange carcass sizes as required and the manufacturing outputs update automatically.
- Change default carcass sizesChange the default carcass sizes to match your own requirements and let the manufacturing outputs update automatically.
- 캐비닛에 올바른 왼쪽 또는 오른쪽 끝 패널을 선택하세요캐비닛에 왼쪽 또는 오른쪽 끝 패널을 추가할 때, 방향은 장치의 도어를 마주 보고 결정됩니다.
- Close a skirting gap with extension parametersClose a gap at the skirting by applying extension parameters to the skirting component.
- Configure front and back skirting on a wardrobeChoose whether a wardrobe has front and back skirting.
- Hide carcass panels you do not needToggle panel visibility to hide the carcass panels you do not need.
- How appliance sizes affect carcass constructionLearn how carcass panel sizes are computed and how choosing an appliance adjusts the partition to fit it.
- Make the greyed-out Top switch available in Carcass Panels VisibilitySet Railing Options > Top > Type to 'Full' so the Top switch in Carcass Panels Visibility becomes available, then use the visibility switches to remove the top panel or front skirting panel.
- Remove back panel behind appliances at cabinet levelAppliance units normally have no back panel by default, so no extra step is needed for them.
- Set carcass back rail for a rail-based back panelMake a cabinet back panel rail-based instead of a full panel by setting the carcass back rail option.
- Set carcass panel thickness and extend fillers to match itMatch your fillers to the 18 mm carcass panel thickness so they line up flush with the carcass.
- Set skirting joint order and remove skirting from pricingChoose which panel sits on top at the skirting joints and exclude any skirting you remove from the pricing quotation and BOQ.
- Snap lofts carcass-to-carcass, not shutter-to-shutterAlign loft units by their carcasses rather than their shutters, since shutters carry a 2 mm gap between them.
- Understand built-in carcass thickness parametersLearn which carcass thickness parameters the software creates automatically and which ones you add yourself.
- Understand how carcass configuration drives panel sizesLearn why panel sizes follow the carcass that was actually built and how to adjust thickness when needed.
- Understand sink unit back panels and railsLearn that sink units default to rails at the back instead of a full back panel.
- Understand what a carcass is in a cabinetLearn which panels make up a carcass and how it can be modified to build any cabinet type.
- Use formulas so extensions follow skirting height automaticallyDrive an extension's value with a formula referencing the skirting height so it updates on its own when that height changes.
- 캐비닛 구조, 걸레받이, 상판, 몸통 패널 맞춤 설정선택한 캐비닛에서 맞춤 설정 탭을 열어 구조, 걸레받이, 상판, 몸통 패널을 설정하세요.
- Add custom support panels and set back panel offset and groovingAdd a support panel with its own core material, finish and label, and configure the back panel offset and grooving depth in the extension parameters.
- 캐비닛 단위의 셔터와 몸통 마감 및 심재 설정속성 패널에서 셔터와 몸통 마감 및 심재를 선택하면 상속하는 셔터가 캐비닛을 따릅니다.
- Account for shutter, skirting and carcass dimensionsAdjust panel sizes for the shutter thickness, skirting buffer and drawer clearance that the carcass figures leave out.
- 셔터와 몸통의 재료 두께 및 마감재를 각각 설정하세요몸통과 셔터의 심재와 마감재를 각각 독립적으로 설정하여 각 구성 요소가 자체 선택 사항을 갖도록 하세요.
- 걸레받이 대신 패널을 바닥까지 연장하기구성 설정의 연장 매개변수를 사용하면 걸레받이가 보이는 대신 패널이 바닥까지 이어지게 할 수 있습니다.
- 뒷판 밖으로 튀어나오는 서랍 고치기사용 가능한 수납장 깊이에 맞는 채널을 선택하여 뒷판 밖으로 튀어나오는 서랍을 해결하세요.
- 몸통 패널과 도어 패널에 대해 경첩 수량이 생성되는 방식경첩이 몸통 패널과 도어 패널의 상호 작용을 기준으로 산출되는 이유와 몸통 패널을 끄면 어떻게 되는지 알아보세요.
- 셔터와 캐커스의 심재와 두께 설정셔터와 캐커스에 BWP, BW, HDMR 등의 심재를 선택하고 각각의 두께를 지정하세요. 뒷판은 기본값으로 6 mm 표준 재질이 적용됩니다.
- Add hardware 사용자 지정 패널 몸통 접합부사용자 지정 패널 간의 몸통-몸통 접합부에 연결 철물과 하드웨어를 수동으로 추가합니다.
- 옷장 구조를 수동으로 변경하고 뒷걸레받이를 끄기슬라이딩 옷장의 구조를 수동으로 변경하고 뒷걸레받이를 꺼서 옷장을 사용자 지정합니다.
- 서랍 높이, 전면 패널 감소 및 몸체 1mm 감소 설정필요한 높이로 서랍 설정 구조와 서랍 레벨 구성을 설정한 다음, 서랍 레벨에서 전면 패널 감소를 설정하십시오.
- 서랍 시스템에 사용자 정의 패널을 추가하고 몸체 재질로 매핑하기서랍 시스템 수준에서 사용자 정의 패널을 추가하고, 패널 수준에서 재질을 설정하여 몸체 재질로 매핑하세요.
- 빈 카카스에서 옷장 내부를 직접 구성하세요카탈로그에서 옷장 옵션을 배치하고 선반과 수직 패널 또는 미리 만들어진 칸막이 구성을 사용하여 내부를 직접 구성하세요.
- 수동 치수 측정을 위해 도어 패널을 활성화하여 몸통에서 도어까지 측정평면도에서 수동 치수 측정용 패널을 활성화하고 도어 패널을 선택하여 몸통에서 도어까지 측정하세요.
- Construction 수준에서 뒷판을 확장합니다뒷판을 확장하려면 Construction 수준으로 이동합니다.
- 옷장 구조를 목재 패널 구성으로 설정목재 패널 구성 섹션을 사용하여 옷장 구조를 설정하고 수직 패널 및 서랍과 같은 내부 및 외부 구성 요소를 추가하십시오.
- Extend a cabinet end panel to the floor or ceilingExtend an end panel added from a cabinet's End Panel section downward to the floor or upward from its own panel using the Width Extension values.
- 걸레받이가 끊기는 틈을 덮도록 하부 패널을 연장하세요패널을 선택하고, 별도의 걸레받이가 끊기게 될 틈을 덮도록 연장하세요.
- 서랍 마감이 몸통 마감을 상속하는 방식서랍 시스템 수준에서 명시적으로 변경하기 전까지 서랍 마감이 몸통의 내부 및 외부 마감을 따르는 방식을 알아보세요.
- 옷장 구성 스타일이 몸체 파라미터를 저장하는 방식Learn which carcass parameters a wardrobe unit construction style holds and how updating the style applies them to the wardrobe.
- 몸통 패널 두께를 사용하여 하부 패널을 안쪽으로 오프셋하기하부 패널을 패널 두께만큼 올려 측면 패널 아래가 아닌 몸통 안쪽에 위치하도록 합니다.
- 뒷판이 있는 몸통에 맞게 서랍 치수 정하기서랍이 뒷판에 닿지 않고 들어가도록 몸통의 사용 가능한 내부 깊이를 계산합니다.
- 옷장 걸레받이 구조에서 전면 패널과 측면 패널 이해하기옷장 걸레받이 구조에서 전면 패널과 측면 패널이 어떻게 구성되는지 알아봅니다.
- 싱크대 레일과 걸레받이 옵션 이해하기싱크대가 상단 레일과 후면 레일로 어떻게 구성되는지, 그리고 캐비닛 걸레받이 옵션에서 걸레받이를 켜거나 끄는 방법을 알아보세요.
- 패널별 표시/숨기기 기능으로 몸통 패널을 숨기거나 삭제하세요캐비닛의 Construction > Carcass > Carcass Panels Visibility에서 개별 몸통 패널을 끄세요.
- Add a custom horizontal panel sized from carcass width and thicknessAdd a horizontal custom panel inside a cabinet and size it from the carcass width, depth and panel thickness so it aligns correctly.
- Assign panel types to split skirting segmentsGive split skirting segments the panel types that let hardware and connector rules tell them apart from unsplit skirting.
- Find panels not following carcass materialSpot panels whose custom core material does not follow the carcass by looking for the custom core property under the core section.
- How finish categories control shutter and carcass surfacesLearn how the four finish categories decide which panel surface a finish is applied to and why choosing correctly matters.
- 하드웨어 규칙이 SKU별로 걸레받이 길이를 집계하는 방법자동 하드웨어 규칙을 위해 시스템이 전체 층에서 걸레받이 SKU별로 걸레받이 길이를 합산하는 방법을 알아보세요.
- Set shelf reveal and back panel grooving values as presetsConfigure shelf reveal and back panel grooving values as presets in your account so you do not have to change them repeatedly for each design.
- Set shutter and carcass core material and thickness from Quick AccessSet the shutter and carcass core material and its thickness from Quick Access.
- Set the partition offset distance inside a carcassLearn what the partition offset value means when you add a partition inside a carcass, so you inset the partition by a distance instead of setting its thickness.
- Target specific panels instead of the broad carcass panelNarrow a rule's panel-type condition so connectors land only on the panels you intend.
- Understand why filler cabinets show a carcass box in floorplanLearn why a filler cabinet appears as a box in plan and what that box's size reflects.
다른 가이드 3
모두 보기 (3)
- Minifix와 다월 배치가 자동화되는 방식캐비닛 몸체에서 Minifix와 다월의 자동 배치를 결정하는 요인을 알아보세요.
- Change internal and external color of a storage boxSet a storage box's carcass color and external finish independently using the relevant color controls.
- How construction values come from account defaultsSkirting and other construction values are populated from your account's default settings.