キャーカス、幅木、仕上げパネル
ガイド:112
- Match carcass, side panel and edge band finishes to the shutterSet the carcass and side panel finishes separately and make edge bands follow the shutter's visible edge band setting.
- 背パネルのオフセットの測定方法と設定方法背パネルのオフセットを設定する場所、キャビネットの外側からどのように測定するか、背パネルの背後に特定の空隙を残す方法について説明します。
- ユニットに幅木を追加し、右側面に表示する木製以外の幅木をオンにし、キャーカス高さを正しく設定して、側面ごとに幅木の表示を有効にします。
- キャビネット本体の外側に扉のプロパティを引き継ぐ見付板を追加するキャビネットに見付板を追加すると、見える仕上げの側板がキャビネット本体の外側に扉のプロパティで配置されます。
- パネルレベルでパネルを編集して、背パネルの厚みを変更するアイランドキッチンで18 mmなど、背パネルに厚いキャーカス厚を設定するには、パネルレベルでその1枚のパネルを編集します。
- 背板の溝のオフセットと延長の設定方法溝付き背板のパネル端からのオフセットと延長深さがどのように定義され、どこで設定するかを説明します。
- ユニットの巾木の種類と高さを設定するユニットごとに木製または木製以外の巾木を選択し、製作オプションから巾木の高さを設定します。
- キャビネット設定でキャビネットの幅木を設定するキャビネット設定でキャビネットの幅木のオプションを確認します。
- Constructionタブで幅木、キャビネット本体のパネル、オフセットを設定するConstructionタブで幅木、キャビネット本体のパネル、背パネルのオフセットがどのように表示されるかを設定し、キャビネットの製造出力がデザインと一致するようにします。
- 1台のキャビネットの本体仕上げを変更するキャビネット単位で本体仕上げを変更すると、選択したキャビネットの本体パネルがすべてまとめて更新され、同じ種類の他のキャビネットには影響しません。
- 背板の溝切りを既定で5 mmに設定する背板の溝切りを既定で5 mmに設定すると、背板は既定でその深さに溝切りされます。
- 背パネルの延長で10 mmのオフセットを使用する方法背パネルの延長が10 mmのオフセットでどのように構成されるかを学びます。
- キッチンキャビネットの幅木がユニット全体の高さに与える影響キッチンキャビネットの約100 mmの幅木が、寸法に表示されるキャarcass高さに加算されてユニット全体の高さになる仕組みを説明します。
- 側パネルまたは側面巾木の間に納まる後ろ巾木後ろ巾木を追加し、側パネルまたは側面巾木の間に納まるようにします。これにより、側パネルが巾木の端を塞ぎます。
- ユニットから幅木を外すSkirting Visibilityの下の前幅木をオフにすると、ユニットの正面に幅木が表示されなくなります。
- ハードウェアを変更して巾木の高さを変更する固定高さのPVC巾木ハードウェア(一般的に100 mmまたは150 mm)を交換して、ユニットの巾木の高さを変更します。
- 自動の7 mm背板溝を理解する背板溝は常に7 mmで、手動で変更することなくデザインに正しく反映されます。
- 壁セクションと検索で壁に幅木を追加する内壁の壁幅木をオンにし、検索して希望の幅木ベースを見つけます。
- 壁に幅木を追加する壁を選択し、wall skirting をオンにすると、その壁に幅木を追加できます。
- 壁セクションのプロパティパネルから壁幅木を適用する壁セクションのプロパティパネルでWall Skirtingをオンにし、壁に適用する幅木の仕上げを選択します。
- シャッターとは別に幅木の仕上げを変更する幅木付きワードローブの幅木に、シャッターの既定の仕上げではなく独自の仕上げを設定します。
- 幅木の高さを修正してパネルが自動調整されるようにする幅木の高さの値を変更すると全体の高さが再適用され、手動で編集しなくてもパネルが調整されます。
- 背板の芯材をキャビネット本体の芯材にリンクするキャビネット設定で各背板の芯材を対応するキャビネット本体の芯材にリンクすると、背板の芯材がすべてのキャビネットに既定で適用されます。
- キャビネットのエンドパネルは、admin portalではなく設計パネルレベルでサイズ変更します設計フェーズでパネルレベルでキャビネットのエンドパネルの奥行きを変更すると、変更は作業中のキャビネットにのみ適用されます。
- スカート(幅木)オプションの奥行きオフセットでスカートを後退させるスカートオプションに奥行きオフセット値を入力して、前面扉からスカートを後退させます。
- キャビネット本体パネルをレールに変換し、レールの奥行きを設定する天板や背板など、選択したキャビネット本体パネルをレールに変換し、そのレールの奥行きを設定できます。
- リンクされた背板コアとラミネート厚みがキャーカスパネルに与える影響リンクされた背板コアがキャビネットのCarcass Back Core Materialを上書きする仕組みと、コアとラミネートがパネル厚みを決める仕組みを学びます。
- 背板の素材を設定・変更する方法背板の素材がデフォルトで6 mmの標準ボードになる仕組みと、異なる厚さや素材が必要な場合の変更方法を説明します。
- ワードローブの背板の溝加工が構築設定に従う仕組みワードローブのSKUとデザイン設定の背板延長値によって、背板が周囲のパネルにどれだけ入り込むかが決まる仕組みを学びます。
- スカートパネルのマイナスの背面延長を使用してスカートのサイズを縮小するパネルエディタでマイナスの延長を適用して、スカートの列を縮小し、スカートの周囲に側面パネルを取り付けます。
- Set end panel depth to carcass level for open unitsStop the end panel at carcass level on a top unit that has no shutter so it aligns with the carcass.
- 他のパネルに載るか、他のパネルの間に入るかをキャ carcass パネルごとに設定します2枚のキャarcass パネルが接する各エッジについて、両方のパネルがパネル厚1枚分ずつサイズ変更されるように、インセット/アウトセットの構造を選択します。
- シナリオがキャビネット本体のパネルと接合パネルをどのように表示するかを理解するシナリオが、まずキャビネット本体のパネルを、次に接合するパネルを、接合する側を面として示してどのように表すかを学びます。
- Why skirting and pelmet options depend on base or wall unitsLearn how a cabinet's mounting plane sets it as a base or wall unit and which skirting, pelmet, cornice and rail options that unlocks.
- キャビネットの構造に側面化粧板を追加または削除する選択したユニットのキャビネット構造設定で、左右の側面化粧板を追加または削除します。
- ワードローブの構造で巾木の高さと扉システムを調整するワードローブと標準キャビネットの巾木の高さまたは扉システムは、ワードローブ構造オプションの3番目のタブから変更します。
- キャビネット全体の幅から本体の幅を計算するキャビネット全体の幅から本体パネルの厚みを2回差し引いて、本体の幅を算出します。
- パネルレベルで巾木のエッジバインディングを変更するパネルレベルで変更することで、巾木エリアに扉とは異なる独自のエッジバインディングを設定できます。
- キャビネット本体の外面仕上げと内面仕上げを選択するキャビネットを選択した後、キャビネットのプロパティパネルにあるそれぞれの素材ピッカーから、キャビネット本体の外面仕上げとキャビネット本体の内面仕上げを選択します。内面ピッカーでは内側の色を設定します。
- Constructionタブで端パネルを縦パネルに変換するConstructionタブで端パネル自身のパネルを縦パネルに変換すると、そのままの位置に残り、縦パネルと同様に棚用コネクターセットとドリル穴が付きます。
- キャビネット本体パネルの芯材の選ばれ方キャビネット本体パネルの芯材がどこから来るか、またパネルがいつ独自の板材を保つかを学びます。
- 胴体用接続金具が自動的に識別・調整される仕組みキャビネットソフトウェアが胴体用接続金具を自動的に識別し、パネルの変数が変わるとその位置と数量を調整する方法を説明します。
- 16 mm HDMR のキャビネット躯体で背板の素材がどのように選ばれるかキャビネット躯体を 16 mm HDMR に設定すると、6 mm HDMR の背板が自動的に適用される仕組みを説明します。
- ワードローブの巾木オプションを設定するSkirting Optionsでワードローブユニットの巾木を設定し、表示する板と巾木の高さを選択します。
- キャビネットを配置する前に、キャビネット本体の芯材と背板の材質の既定値を設定しますキャビネット単位の設定でキャビネット本体の芯材と背板の芯材を選択すると、新しいキャビネットはその材質で追加されます。
- constructionの既定のpartition設定を使用してキャビネットの背パネルを分割するキャビネットを選択し、そのconstructionの既定のpartitionオプションを使用して、背パネルを分割するか、縦仕切りを追加します。
- エンドパネルと側面パネルを別々のパネル種類として理解するキャビネットの側面パネルとエンドパネルが、それぞれ独自の延長設定を持つ別個のパネル種類であることを学びます。
- 躯体パネル厚さの計算式を使って内部寸法を自動調整する手動で計算した内部寸法の代わりに、躯体パネル厚さに基づいてEnter a formulaし、システムが内部空間を正しい値に調整できるようにします。
- Add a custom end panel to a cabinetAdd a custom end panel to a cabinet and it extends on whichever side you add it.
- Add a shell and verticals to an empty wardrobe carcassAdd a shell and verticals to an empty wardrobe carcass, then find the partition options in the selection tree on the left-hand side.
- Sweep Toolでコーニス、モールディング、壁パネルを追加する壁にSweep Toolを使用して、カスタムのコーニス、モールディング、装飾的な壁パネルを追加できます。また、タイル切断のsweepモードを壁モールディングやシャッターのデザインに使用できます。
- Add or change a back panel on an appliance unitAppliance units come with an open back by default so heat can radiate, and you can add or change a closed or coloured back panel in the open part of the construction.
- Add skirting and extra end panels from cabinet constructionConfigure skirting on a unit and add an extra left or right end panel from the cabinet's Construction tab.
- Apply skirting visibility to new unitsTurn on the skirting visibility preference so the front, left, right and back skirting show/hide state is applied to each unit when it is added.
- Bulk edit drawer carcass thickness and set defaultSet the drawer carcass thickness for all drawers at once, knowing individual drawers can still be overridden later if a different thickness is needed.
- Change carcass sizes to update manufacturing outputsChange carcass sizes as required and the manufacturing outputs update automatically.
- Change default carcass sizesChange the default carcass sizes to match your own requirements and let the manufacturing outputs update automatically.
- キャビネットに適切な左または右の側面パネルを選択するユニットの扉に向かった状態で左右が決まることに注意して、キャビネットに左または右の側面パネルを追加します。
- Close a skirting gap with extension parametersClose a gap at the skirting by applying extension parameters to the skirting component.
- Configure front and back skirting on a wardrobeChoose whether a wardrobe has front and back skirting.
- Hide carcass panels you do not needToggle panel visibility to hide the carcass panels you do not need.
- How appliance sizes affect carcass constructionLearn how carcass panel sizes are computed and how choosing an appliance adjusts the partition to fit it.
- Make the greyed-out Top switch available in Carcass Panels VisibilitySet Railing Options > Top > Type to 'Full' so the Top switch in Carcass Panels Visibility becomes available, then use the visibility switches to remove the top panel or front skirting panel.
- Remove back panel behind appliances at cabinet levelAppliance units normally have no back panel by default, so no extra step is needed for them.
- Set carcass back rail for a rail-based back panelMake a cabinet back panel rail-based instead of a full panel by setting the carcass back rail option.
- Set carcass panel thickness and extend fillers to match itMatch your fillers to the 18 mm carcass panel thickness so they line up flush with the carcass.
- Set skirting joint order and remove skirting from pricingChoose which panel sits on top at the skirting joints and exclude any skirting you remove from the pricing quotation and BOQ.
- Snap lofts carcass-to-carcass, not shutter-to-shutterAlign loft units by their carcasses rather than their shutters, since shutters carry a 2 mm gap between them.
- Understand built-in carcass thickness parametersLearn which carcass thickness parameters the software creates automatically and which ones you add yourself.
- Understand how carcass configuration drives panel sizesLearn why panel sizes follow the carcass that was actually built and how to adjust thickness when needed.
- Understand sink unit back panels and railsLearn that sink units default to rails at the back instead of a full back panel.
- Understand what a carcass is in a cabinetLearn which panels make up a carcass and how it can be modified to build any cabinet type.
- Use formulas so extensions follow skirting height automaticallyDrive an extension's value with a formula referencing the skirting height so it updates on its own when that height changes.
- キャビネットの構造、幅木、天板、胴板をカスタマイズ選択したキャビネットのカスタマイズタブを開き、構造、幅木、天板、胴板を設定します。
- Add custom support panels and set back panel offset and groovingAdd a support panel with its own core material, finish and label, and configure the back panel offset and grooving depth in the extension parameters.
- キャビネット単位の扉とキャ carcass の仕上げ・芯材を設定するプロパティパネルで扉とキャ carcass の仕上げと芯材を選択すると、継承する扉はキャビネットに従います。
- シャッター、幅木、キャカスの寸法を考慮するキャカスの数値に含まれないシャッターの厚み、幅木のバッファー、引き出しのクリアランスに合わせてパネルのサイズを調整します。
- 扉とキャビネット本体の材料厚みと仕上げを個別に設定するキャビネット本体と扉の芯材と仕上げを個別に設定し、各構成部品がそれぞれの選択を保持するようにします。
- 巾木の代わりにパネルを床まで延長する構築設定の延長パラメータを使用すると、巾木を表示する代わりにパネルを床まで連続させることができます。
- 背板から突き出る引き出しを修正するキャビネットの有効奥行きに合うレールを選ぶことで、背板から突き出る引き出しを解決できます。
- 躯体パネルと扉パネルのヒンジ数量がどのように生成されるかヒンジが躯体パネルと扉パネルの相互作用から数えられる理由と、躯体パネルをオフにした場合にどうなるかを説明します。
- 扉とキャビネット本体の芯材と厚さを設定する扉とキャビネット本体にはBWP、BW、HDMRなどの芯材を選択し、それぞれの厚さを指定します。背板は標準材6 mmが初期値です。
- Add hardware to custom panel carcass jointsAdd connectors and hardware manually at carcass-to-carcass junctions between custom panels.
- ワードローブの構造を手動で変更し、背面スカートをオフにするワードローブの構造を手動で変更し、引き戸式ワードローブの背面スカートをオフにして、ワードローブをカスタマイズします。
- 引き出しの高さ、前板の縮小、キャ carcass の1mm縮小を設定します必要な高さで引き出し設定構造と引き出しレベルの構造を構成し、引き出しレベルで前板の縮小を設定します。
- Add custom panels to a drawer system and map them as carcass materialAdd custom panels at the drawer system level and set their material at any panel level to map them as carcass material.
- 空のキャ carcass からワードローブの内部を自分で構築するカタログからワードローブのオプションを配置し、棚と縦パネル、または既製の仕切り構成を使って内部を自分で構築します。
- 手動寸法取りでキャビネット本体から扉までを測定するための扉パネルを有効にする手動寸法取り用のパネルを有効にし、扉パネルを選択すると、平面図でキャビネット本体から扉までを測定できます。
- Constructionレベルで背板を延長する背板を延長するには、Constructionレベルに移動します。
- キャビネットパネル構法でワードローブの構造を設定するキャビネットパネル構法セクションを使用してワードローブの構造を設定し、縦パネルや引き出しなどの内部・外部部品を追加します。
- キャビネットの化粧側板を床または天井まで延長するキャビネットのEnd Panelセクションから追加した化粧側板を、Width Extensionの値を使って床まで下方向に、または化粧側板自身のパネルから上方向に延長します。
- 下部パネルを延長して、幅木が途切れる隙間をふさぐパネルを選択し、別の幅木では途切れてしまう隙間をふさぐように延長します。
- 引き出しの仕上げがキャビネット本体の仕上げを継承する仕組み引き出しシステムのレベルで明示的に変更するまで、引き出しの仕上げがキャビネット本体の内側と外側の仕上げに従う仕組みを説明します。
- ワードローブの構造スタイルがキャーカスパラメータを保存する方法ワードローブユニットの構造スタイルが保持するキャーカスパラメータと、スタイルを更新したときにそれがワードローブに適用される方法を説明します。
- キャビネットの底板を側板の板厚分だけ内側にオフセットする底板を板厚1枚分上げて、側板の下ではなくキャビネット本体の内側に収まるようにします。
- 背板付きのキャビネット本体に合う引き出しのサイズ設定引き出しが背板に当たらずに収まるよう、キャビネット本体の有効内寸法(奥行き)を算出します。
- ワードローブの蹴込み構造における前パネルと側パネルの理解ワードローブの蹴込み構造で前パネルと側パネルがどのように構成されるかを学びます。
- シンクユニットのレールと巾木のオプションを理解するシンクユニットが上部と背面のレールでどのように構成されるか、またキャビネットの巾木オプションから巾木をオンまたはオフにする方法を学びます。
- Hide or delete carcass panels via panel-level visibilitySwitch off a single carcass panel from the cabinet's Construction > Carcass > Carcass Panels Visibility.
- Add a custom horizontal panel sized from carcass width and thicknessAdd a horizontal custom panel inside a cabinet and size it from the carcass width, depth and panel thickness so it aligns correctly.
- Assign panel types to split skirting segmentsGive split skirting segments the panel types that let hardware and connector rules tell them apart from unsplit skirting.
- Find panels not following carcass materialSpot panels whose custom core material does not follow the carcass by looking for the custom core property under the core section.
- How finish categories control shutter and carcass surfacesLearn how the four finish categories decide which panel surface a finish is applied to and why choosing correctly matters.
- スカート材のハードウェアルールがSKUごとにスカート材の長さを集計する方法自動ハードウェアルールのために、システムがフロア全体でスカート材SKUごとにスカート材の長さを合計する方法を説明します。
- Set shelf reveal and back panel grooving values as presetsConfigure shelf reveal and back panel grooving values as presets in your account so you do not have to change them repeatedly for each design.
- Set shutter and carcass core material and thickness from Quick AccessSet the shutter and carcass core material and its thickness from Quick Access.
- Set the partition offset distance inside a carcassLearn what the partition offset value means when you add a partition inside a carcass, so you inset the partition by a distance instead of setting its thickness.
- Target specific panels instead of the broad carcass panelNarrow a rule's panel-type condition so connectors land only on the panels you intend.
- Understand why filler cabinets show a carcass box in floorplanLearn why a filler cabinet appears as a box in plan and what that box's size reflects.
その他のガイド 3
すべて表示(3)
- ミニフィックスとダボの配置が自動化される仕組みキャビネット本体のミニフィックスとダボの自動配置が何によって決まるかを学びます。
- Change internal and external color of a storage boxSet a storage box's carcass color and external finish independently using the relevant color controls.
- How construction values come from account defaultsSkirting and other construction values are populated from your account's default settings.