Carcass, skirting and finishing panels
Guides: 112
- Match carcass, side panel and edge band finishes to the shutterSet the carcass and side panel finishes separately and make edge bands follow the shutter's visible edge band setting.
- How back panel offset is measured and setLearn where the back panel offset is set, how it is measured from the outside of the cabinet, and how to leave a specific clear void behind the back panel.
- Add skirting to units and show it on the right sidesTurn on non-wooden skirting, set the carcass height correctly and enable skirting visibility per side.
- Add an end panel that takes shutter properties outside the carcassAdd an end panel to a cabinet so a visible finished side panel sits outside the carcass with the shutter's properties.
- Change a back panel thickness by editing the panel at panel levelGive a back panel a thicker carcass thickness, such as 18 mm for an island kitchen, by editing that single panel at panel level.
- How back panel groove offset and extension are configuredLearn how a grooved back panel's offset from the panel edge and its extension depth are defined and where to set them.
- Set skirting type and height on a unitChoose wooden or non-wooden skirting per unit and set the skirting height from the construction options.
- Configure cabinet skirting in cabinet settingsFind the cabinet skirting options in the cabinet configuration.
- Configure skirting, carcass panels and offsets in Construction tabSet how skirting, carcass panels and back panel offsets appear in the Construction tab so your cabinet's manufacturing output matches the design.
- Change carcass finish for one cabinetChange the carcass finish at cabinet level to update all carcass panels of the selected cabinet together, without affecting other cabinets of the same kind.
- Set the default back panel groove to 5 mmSet the default back panel grooving to 5 mm so back panels are grooved at that depth by default.
- How back panel extension uses a 10 mm offsetLearn how the back panel extension is built with a 10 mm offset.
- How kitchen cabinet skirting affects total unit heightLearn how the roughly 100 mm skirting on a kitchen cabinet adds to the carcass height shown in the dimensions to give the total unit height.
- Inset back skirting between side panels or side skirtingAdd a back skirting so it sits inset between the side panels or side skirting, letting the side panels close the skirting ends.
- Remove the skirting from a unitSwitch off the front skirting under Skirting Visibility so the unit no longer shows skirting at the front.
- Change skirting height by changing the hardwareChange a unit's skirting height by swapping the fixed-height PVC skirting hardware, commonly 100 mm or 150 mm.
- Understand the automatic 7 mm back panel grooveThe back panel groove is always 7 mm and comes correctly in the design without any manual change.
- Add skirting to walls via wall sections and searchTurn on wall skirting for your inner walls and find the skirting base you want by searching for it.
- Add wall skirting to a wallSelect a wall and toggle on wall skirting to add skirting to it.
- Apply wall skirting from the wall section's properties panelTurn on Wall Skirting in the wall section's properties panel and pick the skirting finish to apply to the wall.
- Change skirting finish independently of shutterGive the skirting of a skirting wardrobe its own finish instead of the shutter's default.
- Fix skirting height so panels adjust automaticallyChange the skirting height value so the overall height re-applies and the panel adjusts without manual edits.
- Link back panel core material to carcass core materialLink each back core material to its matching carcass core material in cabinet preferences so the back panel core applies by default across all cabinets.
- Resize cabinet end panel at design panel level, not admin portalChange a cabinet end panel's depth in the design phase at the panel level so the change applies only to the cabinet you are working on.
- Set recessed skirting using depth offset in skirting optionsRecess the skirting from the front shutter by entering a depth offset value in the skirting options.
- Convert a carcass panel into rails and set rail depthTurn a selected carcass panel such as the top or back into rails and control how deep those rails are.
- How linked back panel cores and laminate thicknesses affect carcass panelsLearn how a linked back panel core overrides the cabinet's Carcass Back Core Material and how cores plus laminates set panel thickness.
- How the back panel material is set and changedLearn how the back panel material defaults to a 6 mm standard board and how to change it when a different thickness or material is required.
- How wardrobe back panel grooving follows construction settingsLearn how the back panel extension values from the wardrobe SKU and design preferences set how far back panels run into the surrounding panels.
- Reduce skirting size using negative back extension on skirting panelShrink a skirting run and fit side panels around the skirting by applying negative extensions in the panel editor.
- Set end panel depth to carcass level for open unitsStop the end panel at carcass level on a top unit that has no shutter so it aligns with the carcass.
- Set which carcass panel sits on or between the otherPick the inset/outset construction for each edge where two carcass panels meet so both panels resize by one panel thickness.
- Understand how scenarios list carcass and meeting panelsLearn how a scenario names the carcass panel first and the panel it meets second, with the meeting side given as a face.
- Why skirting and pelmet options depend on base or wall unitsLearn how a cabinet's mounting plane sets it as a base or wall unit and which skirting, pelmet, cornice and rail options that unlocks.
- Add or remove an end panel from cabinet constructionAdd or remove a left or right end panel on a selected unit from its cabinet construction settings.
- Adjust skirting height and shutter system under wardrobe constructionChange the skirting height or shutter system for wardrobes and standard cabinets from the third tab under wardrobe construction options.
- Calculate carcass width from overall cabinet widthWork out the carcass width by taking the overall cabinet width and subtracting twice the carcass panel thickness.
- Change edge binding for skirting at panel levelGive a skirting area its own edge binding, different from the shutter, by changing it at panel level.
- Choose carcass external and internal finishesPick the carcass external finish and the carcass internal finish from their own material pickers in the cabinet's properties panel after selecting the cabinet, with the internal picker setting the inside colour.
- Convert an end panel to an upright from its Construction tabConvert an end panel's own panel on the Construction tab to an upright so it stays in place and gains shelf connector sets and drill holes like an upright.
- How a carcass panel's core is chosenLearn where a carcass panel's core comes from and when the panel keeps its own board.
- How carcass connectors are identified and adjusted automaticallyLearn how the cabinet software identifies carcass connectors for you and adjusts their position and quantity as panel variables change.
- How the back panel material is chosen for a 16 mm HDMR carcassLearn how setting a cabinet carcass to 16 mm HDMR automatically applies a 6 mm HDMR back panel.
- Set a wardrobe's skirting optionsSet the skirting for a wardrobe unit with its Skirting Options, choosing which planks show and how tall the skirting is.
- Set carcass core and back-panel material defaults before placing cabinetsChoose the carcass core and back-panel core materials in the cabinet-level preference so new cabinets are added with them.
- Split a cabinet back panel using construction default partition settingsSelect a cabinet and use its construction default partition options to split the back panel or add a vertical divider.
- Understand end panels and side panels as separate panel typesLearn how a cabinet's side panels and end panels are distinct panel types with their own extension settings.
- Use carcass panel thickness formula to auto-adjust internal dimensionsEnter a formula based on carcass panel thickness instead of a manually calculated internal dimension, and let the system adjust the internal space to the correct value.
- Add a custom end panel to a cabinetAdd a custom end panel to a cabinet and it extends on whichever side you add it.
- Add a shell and verticals to an empty wardrobe carcassAdd a shell and verticals to an empty wardrobe carcass, then find the partition options in the selection tree on the left-hand side.
- Add cornices, mouldings and wall panelling with Sweep ToolUse the Sweep Tool on walls to add custom cornices, mouldings and decorative wall panelling, and use sweep mode in tiling cutting for wall mouldings and shutter designs.
- Add or change a back panel on an appliance unitAppliance units come with an open back by default so heat can radiate, and you can add or change a closed or coloured back panel in the open part of the construction.
- Add skirting and extra end panels from cabinet constructionConfigure skirting on a unit and add an extra left or right end panel from the cabinet's Construction tab.
- Apply skirting visibility to new unitsTurn on the skirting visibility preference so the front, left, right and back skirting show/hide state is applied to each unit when it is added.
- Bulk edit drawer carcass thickness and set defaultSet the drawer carcass thickness for all drawers at once, knowing individual drawers can still be overridden later if a different thickness is needed.
- Change carcass sizes to update manufacturing outputsChange carcass sizes as required and the manufacturing outputs update automatically.
- Change default carcass sizesChange the default carcass sizes to match your own requirements and let the manufacturing outputs update automatically.
- Choose the correct left or right end panel for a cabinetAdd a left or right end panel to a cabinet knowing that the side is decided by facing the shutters of the unit.
- Close a skirting gap with extension parametersClose a gap at the skirting by applying extension parameters to the skirting component.
- Configure front and back skirting on a wardrobeChoose whether a wardrobe has front and back skirting.
- Hide carcass panels you do not needToggle panel visibility to hide the carcass panels you do not need.
- How appliance sizes affect carcass constructionLearn how carcass panel sizes are computed and how choosing an appliance adjusts the partition to fit it.
- Make the greyed-out Top switch available in Carcass Panels VisibilitySet Railing Options > Top > Type to 'Full' so the Top switch in Carcass Panels Visibility becomes available, then use the visibility switches to remove the top panel or front skirting panel.
- Remove back panel behind appliances at cabinet levelAppliance units normally have no back panel by default, so no extra step is needed for them.
- Set carcass back rail for a rail-based back panelMake a cabinet back panel rail-based instead of a full panel by setting the carcass back rail option.
- Set carcass panel thickness and extend fillers to match itMatch your fillers to the 18 mm carcass panel thickness so they line up flush with the carcass.
- Set skirting joint order and remove skirting from pricingChoose which panel sits on top at the skirting joints and exclude any skirting you remove from the pricing quotation and BOQ.
- Snap lofts carcass-to-carcass, not shutter-to-shutterAlign loft units by their carcasses rather than their shutters, since shutters carry a 2 mm gap between them.
- Understand built-in carcass thickness parametersLearn which carcass thickness parameters the software creates automatically and which ones you add yourself.
- Understand how carcass configuration drives panel sizesLearn why panel sizes follow the carcass that was actually built and how to adjust thickness when needed.
- Understand sink unit back panels and railsLearn that sink units default to rails at the back instead of a full back panel.
- Understand what a carcass is in a cabinetLearn which panels make up a carcass and how it can be modified to build any cabinet type.
- Use formulas so extensions follow skirting height automaticallyDrive an extension's value with a formula referencing the skirting height so it updates on its own when that height changes.
- Customize cabinet construction, skirting, countertop and carcass panelsOpen the customize tab on a selected cabinet to set its construction, skirting, countertop and carcass panels.
- Add custom support panels and set back panel offset and groovingAdd a support panel with its own core material, finish and label, and configure the back panel offset and grooving depth in the extension parameters.
- Set cabinet-level shutter and carcass finishes and coresPick the shutter and carcass finishes and core materials from the properties panel so inheriting shutters follow the cabinet.
- Account for shutter, skirting and carcass dimensionsAdjust panel sizes for the shutter thickness, skirting buffer and drawer clearance that the carcass figures leave out.
- Configure shutter and carcass material thickness and finishes separatelySet the core material and finish for the carcass and the shutter independently so each component carries its own selection.
- Extend a panel down to the floor instead of skirtingMake a panel continue to the floor instead of showing skirting by using the extension parameters in its construction settings.
- Fix a drawer that protrudes past the back panelResolve a drawer sticking out past the back panel by choosing a channel that matches the usable cabinet depth.
- How hinge quantities are generated for carcass and shutter panelsLearn why hinges are counted from the interaction between a carcass panel and a shutter panel, and what happens when the carcass panel is turned off.
- Set shutter and carcass core material and thicknessChoose a core material such as BWP, BW or HDMR for shutters and carcasses and give each a thickness, with the back panel defaulting to 6 mm standard material.
- Add hardware to custom panel carcass jointsAdd connectors and hardware manually at carcass-to-carcass junctions between custom panels.
- Manually change wardrobe construction and turn off back skirtingCustomize a wardrobe by manually changing its construction and turning off the back skirting for a sliding wardrobe.
- Set drawer heights, front panel reduction and carcass 1mm reductionConfigure the drawer settings structure and drawer-level construction with the required heights, then set the front panel reduction at drawer level.
- Add custom panels to a drawer system and map them as carcass materialAdd custom panels at the drawer system level and set their material at any panel level to map them as carcass material.
- Build wardrobe internals yourself from an empty carcassPlace a wardrobe option from the catalogue and build its internals yourself using shelves and vertical panels or a ready-made partition configuration.
- Enable shutter panel for manual dimensioning to measure carcass to shutterMeasure from carcass to shutter in the floor plan by enabling panels for manual dimensioning and selecting the shutter panel.
- Extend the back panel at Construction levelNavigate to the Construction level to extend the back panel.
- Configure wardrobe structure with Carcass panel constructionUse the Carcass panel construction section to configure wardrobe structure and add internal and external components such as vertical panels and drawers.
- Extend a cabinet end panel to the floor or ceilingExtend an end panel added from a cabinet's End Panel section downward to the floor or upward from its own panel using the Width Extension values.
- Extend the bottom panel to cover a gap where the skirting breaksSelect the panel and extend it to cover the gap where a separate skirting would otherwise break.
- How drawer finishes inherit carcass finishesLearn how drawer finishes follow the carcass internal and external finish until you change them explicitly at the drawer system level.
- How wardrobe construction style stores carcass parametersLearn which carcass parameters a wardrobe unit construction style holds and how updating the style applies them to the wardrobe.
- Offset a cabinet bottom panel inward using carcass panel thicknessRaise a bottom panel by one panel thickness so it sits inside the carcass instead of below the side panels.
- Size a drawer to fit a carcass with a back panelWork out the usable internal depth of a carcass so a drawer fits without hitting the back panel.
- Understand front and side panels in wardrobe skirting constructionLearn how the front panel and the side panel are built in wardrobe skirting construction.
- Understand sink unit rails and skirting optionsLearn how sink units are built with top and back rails and how to turn skirting on or off from the cabinet skirting options.
- Hide or delete carcass panels via panel-level visibilitySwitch off a single carcass panel from the cabinet's Construction > Carcass > Carcass Panels Visibility.
- Add a custom horizontal panel sized from carcass width and thicknessAdd a horizontal custom panel inside a cabinet and size it from the carcass width, depth and panel thickness so it aligns correctly.
- Assign panel types to split skirting segmentsGive split skirting segments the panel types that let hardware and connector rules tell them apart from unsplit skirting.
- Find panels not following carcass materialSpot panels whose custom core material does not follow the carcass by looking for the custom core property under the core section.
- How finish categories control shutter and carcass surfacesLearn how the four finish categories decide which panel surface a finish is applied to and why choosing correctly matters.
- How skirting hardware rules aggregate skirting length per SKULearn how the system totals skirting length per skirting SKU across the whole floor for automatic hardware rules.
- Set shelf reveal and back panel grooving values as presetsConfigure shelf reveal and back panel grooving values as presets in your account so you do not have to change them repeatedly for each design.
- Set shutter and carcass core material and thickness from Quick AccessSet the shutter and carcass core material and its thickness from Quick Access.
- Set the partition offset distance inside a carcassLearn what the partition offset value means when you add a partition inside a carcass, so you inset the partition by a distance instead of setting its thickness.
- Target specific panels instead of the broad carcass panelNarrow a rule's panel-type condition so connectors land only on the panels you intend.
- Understand why filler cabinets show a carcass box in floorplanLearn why a filler cabinet appears as a box in plan and what that box's size reflects.
More guides 3
Show all (3)
- How Minifix and dowel placement is automatedLearn what drives the automatic placement of Minifix and dowels in a carcass.
- Change internal and external color of a storage boxSet a storage box's carcass color and external finish independently using the relevant color controls.
- How construction values come from account defaultsSkirting and other construction values are populated from your account's default settings.