कारकास, स्कर्टिंग और फिनिशिंग panel
गाइड: 112
- कारकास, side panel और edge band फिनिश को shutter से मिलाएँकारकास और side panel की फिनिश अलग-अलग सेट करें और edge band को shutter की दृश्यमान edge band सेटिंग का पालन करने दें।
- back panel offset को कैसे मापा और सेट किया जाता हैजानें कि back panel offset कहाँ सेट होता है, इसे कैबिनेट के बाहर से कैसे मापा जाता है, और back panel के पीछे एक विशिष्ट खाली जगह कैसे छोड़ी जाती है।
- unit में skirting जोड़ें और इसे right side पर दिखाएँnon-wooden skirting चालू करें, carcass height सही ढंग से सेट करें और प्रत्येक side के लिए skirting visibility सक्षम करें।
- end panel जोड़ें जो carcass के बाहर shutter properties लेता हैकैबिनेट में end panel जोड़ें ताकि एक दिखने वाला finished side panel shutter की properties के साथ carcass के बाहर रहे।
- panel level पर panel को edit करके back panel thickness बदलेंpanel level पर उस एक panel को edit करके back panel को मोटी carcass thickness दें, जैसे island kitchen के लिए 18 mm।
- back panel groove offset और extension कैसे कॉन्फ़िगर किए जाते हैंजानें कि grooved back panel का panel edge से offset और उसकी extension depth कैसे परिभाषित होती है और उन्हें कहाँ सेट करना है।
- unit पर skirting type और height सेट करेंप्रत्येक unit के लिए wooden या non-wooden skirting चुनें और construction option से skirting height सेट करें।
- कैबिनेट सेटिंग्स में कैबिनेट स्कर्टिंग कॉन्फ़िगर करेंकैबिनेट कॉन्फ़िगरेशन में कैबिनेट स्कर्टिंग के विकल्प खोजें।
- Construction टैब में skirting, carcass panel और offset कॉन्फ़िगर करेंConstruction टैब में सेट करें कि skirting, carcass panel और back panel offset कैसे दिखें, ताकि आपके कैबिनेट का manufacturing आउटपुट डिज़ाइन से मेल खाए।
- एक कैबिनेट के लिए carcass finish बदलेंचयनित कैबिनेट के सभी carcass panel एक साथ अपडेट करने के लिए cabinet level पर carcass finish बदलें; इससे उसी प्रकार के अन्य कैबिनेट प्रभावित नहीं होंगे।
- default back panel groove को 5 mm पर सेट करेंdefault back panel grooving को 5 mm पर सेट करें, ताकि back panels डिफ़ॉल्ट रूप से उस गहराई पर grooved हों।
- back panel extension 10 mm offset का उपयोग कैसे करता हैजानें कि back panel extension 10 mm offset के साथ कैसे बनाया जाता है।
- kitchen कैबिनेट स्कर्टिंग total unit ऊँचाई को कैसे प्रभावित करती हैजानें कि kitchen कैबिनेट पर लगभग 100 mm की स्कर्टिंग dimension में दिखाई गई कार्कस ऊँचाई में जुड़कर total unit ऊँचाई कैसे बनाती है।
- side panel या side skirting के बीच inset back skirtingback skirting इस तरह जोड़ें कि वह side panel या side skirting के बीच inset रहे, जिससे side panel skirting के सिरों को बंद कर दें।
- unit से skirting हटाएँunit के आगे skirting न दिखे, इसके लिए Skirting Visibility के अंतर्गत front skirting बंद करें।
- हार्डवेयर बदलकर स्कर्टिंग की ऊँचाई बदलेंfixed-ऊँचाई वाले PVC स्कर्टिंग hardware को बदलकर unit की स्कर्टिंग ऊँचाई बदलें, जो सामान्यतः 100 mm या 150 mm होती है।
- स्वचालित 7 mm back panel groove को समझेंback panel groove हमेशा 7 mm होता है और बिना किसी मैन्युअल बदलाव के डिज़ाइन में सही ढंग से आता है।
- wall section और search के माध्यम से wall पर skirting जोड़ेंअपने inner wall के लिए wall skirting चालू करें और search करके अपना मनचाहा skirting base खोजें।
- wall पर wall skirting जोड़ेंwall चुनें और उस पर skirting जोड़ने के लिए wall skirting को चालू करें।
- wall section के properties panel से wall skirting लागू करेंwall section के properties panel में Wall Skirting चालू करें और wall पर लागू करने के लिए skirting finish चुनें।
- shutter से स्वतंत्र रूप से skirting की फिनिश बदलेंskirting wardrobe के skirting को shutter की डिफ़ॉल्ट फिनिश के बजाय अपनी फिनिश दें।
- panels को स्वचालित रूप से समायोजित करने के लिए skirting height निर्धारित करेंskirting height का मान बदलें ताकि समग्र height फिर से लागू हो और panel बिना मैन्युअल संपादन के समायोजित हो जाए।
- back panel core material को carcass core material से लिंक करेंcabinet preferences में प्रत्येक back core material को उसके मिलते-जुलते carcass core material से लिंक करें, ताकि back panel core डिफ़ॉल्ट रूप से सभी कैबिनेट पर लागू हो।
- कैबिनेट end panel का आकार design panel level पर बदलें, admin portal में नहींdesign चरण में panel level पर कैबिनेट end panel की गहराई बदलें, ताकि बदलाव केवल उसी कैबिनेट पर लागू हो जिस पर आप काम कर रहे हैं।
- skirting options में depth offset का उपयोग करके recessed skirting सेट करेंskirting options में depth offset मान दर्ज करके skirting को front shutter से recess करें।
- carcass panel को rails में बदलें और rail depth सेट करेंचयनित carcass panel जैसे top या back को rails में बदलें और नियंत्रित करें कि वे rails कितने गहरे हों।
- लिंक किए गए back panel core और laminate thickness का carcass panel पर क्या प्रभाव पड़ता हैजानें कि लिंक किया गया back panel core कैबिनेट के Carcass Back Core Material को कैसे ओवरराइड करता है और core तथा laminate मिलकर panel thickness कैसे तय करते हैं।
- back panel material कैसे सेट और बदला जाता हैजानें कि back panel material डिफ़ॉल्ट रूप से 6 mm standard board कैसे होता है और जब अलग thickness या material आवश्यक हो तो इसे कैसे बदलें।
- How wardrobe back panel grooving follows construction settingsLearn how the back panel extension values from the wardrobe SKU and design preferences set how far back panels run into the surrounding panels.
- skirting panel पर negative extension का उपयोग करके skirting का आकार घटाएँpanel editor में negative extension लगाकर skirting run को छोटा करें और skirting के चारों ओर side panel फिट करें।
- खुले unit के लिए end panel की गहराई को carcass स्तर पर सेट करेंजिस top unit में shutter नहीं है, उसमें end panel को carcass स्तर पर रोकें ताकि वह carcass के साथ संरेखित हो।
- Set which carcass panel sits on or between the otherPick the inset/outset construction for each edge where two carcass panels meet so both panels resize by one panel thickness.
- समझें कि scenarios carcass panel और meeting panel को कैसे सूचीबद्ध करते हैंजानें कि एक scenario पहले carcass panel का नाम कैसे लेता है और दूसरे में उस panel का जिससे वह मिलता है, और meeting side को face के रूप में दिया जाता है।
- स्कर्टिंग और पेलमेट विकल्प base या wall unit पर क्यों निर्भर करते हैंजानें कि कैबिनेट का माउंटिंग प्लेन उसे base या wall unit के रूप में कैसे तय करता है और इससे स्कर्टिंग, पेलमेट, कॉर्निस और रेल के कौन-से विकल्प खुलते हैं।
- Cabinet construction से end panel जोड़ें या हटाएँचयनित unit की cabinet construction settings से बाएँ या दाएँ end panel जोड़ें या हटाएँ।
- wardrobe construction के अंतर्गत skirting की ऊँचाई और shutter system समायोजित करेंwardrobe construction option के अंतर्गत तीसरे टैब से wardrobe और standard cabinet के लिए skirting की ऊँचाई या shutter system बदलें।
- कुल कैबिनेट चौड़ाई से कारकास चौड़ाई की गणना करेंकारकास चौड़ाई निकालने के लिए कुल कैबिनेट चौड़ाई लें और उसमें से carcass panel thickness का दोगुना घटाएँ।
- panel level पर skirting के लिए edge binding बदलेंकिसी skirting area को panel level पर बदलकर shutter से अलग अपनी edge binding दें।
- carcass external finish और internal finish चुनेंकैबिनेट चुनने के बाद कैबिनेट के properties panel में उनके अपने material pickers से carcass external finish और carcass internal finish चुनें; internal picker अंदर का रंग सेट करता है।
- Construction टैब से end panel को upright में बदलेंConstruction टैब पर end panel के अपने panel को upright में बदलें, ताकि वह अपनी जगह पर बना रहे और upright की तरह shelf connector सेट और drill holes प्राप्त करे।
- carcass panel के core का चयन कैसे होता हैजानें कि carcass panel का core कहाँ से आता है और panel कब अपना board रखता है।
- कारकैस connector स्वचालित रूप से कैसे पहचाने और समायोजित किए जाते हैंजानें कि कैबिनेट सॉफ़्टवेयर आपके लिए कारकैस connector कैसे पहचानता है और panel वेरिएबल बदलने पर उनकी स्थिति और संख्या कैसे समायोजित करता है।
- 16 mm HDMR cabinet carcass के लिए back panel material कैसे चुना जाता हैजानें कि cabinet carcass को 16 mm HDMR पर सेट करने पर 6 mm HDMR back panel स्वतः लागू हो जाता है।
- wardrobe के skirting विकल्प सेट करेंSkirting Options से wardrobe unit के लिए skirting सेट करें और चुनें कि कौन-से प्लैंक दिखें तथा skirting कितनी ऊँची हो।
- कैबिनेट रखने से पहले carcass core और back-panel material के डिफ़ॉल्ट सेट करेंकैबिनेट-स्तरीय preference में carcass core और back-panel core material चुनें ताकि नए कैबिनेट इन्हीं के साथ जोड़े जाएँ।
- construction default partition settings का उपयोग करके cabinet के back panel को split करेंएक cabinet चुनें और back panel को split करने या vertical divider जोड़ने के लिए उसके construction default partition विकल्पों का उपयोग करें।
- end panel और side panel को अलग-अलग panel type के रूप में समझेंजानें कि कैबिनेट के side panel और end panel अलग-अलग panel type हैं, जिनकी अपनी extension सेटिंग्स होती हैं।
- आंतरिक dimension को स्वतः समायोजित करने के लिए carcass panel thickness सूत्र का उपयोग करेंEnter a formula को मैन्युअल रूप से गणना किए गए आंतरिक dimension के बजाय carcass panel thickness पर आधारित करें, और सिस्टम को आंतरिक स्थान को सही मान पर समायोजित करने दें।
- कैबिनेट में कस्टम end panel जोड़ेंकैबिनेट में कस्टम end panel जोड़ें और यह जिस भी side पर जोड़ा जाए, वहाँ तक फैलता है।
- खाली wardrobe carcass में shell और verticals जोड़ेंखाली wardrobe carcass में shell और verticals जोड़ें, फिर left-hand side पर selection tree में partition विकल्प खोजें।
- Sweep Tool से cornices, mouldings और wall panelling जोड़ेंwall पर custom cornices, mouldings और सजावटी wall panelling जोड़ने के लिए Sweep Tool का उपयोग करें, और wall mouldings तथा shutter design के लिए tiling cutting में sweep mode का उपयोग करें।
- Appliance unit पर back panel जोड़ें या बदलेंAppliance units डिफ़ॉल्ट रूप से खुले back के साथ आते हैं ताकि गर्मी निकल सके, और आप construction के खुले part में बंद या रंगीन back panel जोड़ या बदल सकते हैं।
- Cabinet construction से skirting और extra end panel जोड़ेंकिसी unit पर skirting कॉन्फ़िगर करें और cabinet के Construction टैब से extra left या right end panel जोड़ें।
- नए unit पर skirting visibility लागू करेंskirting visibility preference चालू करें ताकि front, left, right और back skirting की show/hide स्थिति प्रत्येक unit पर लागू हो जब वह जोड़ा जाए।
- drawer carcass thickness को बल्क एडिट करें और डिफ़ॉल्ट सेट करेंसभी drawer के लिए एक साथ drawer carcass thickness सेट करें। ध्यान रखें कि अलग thickness की आवश्यकता होने पर व्यक्तिगत drawer को बाद में ओवरराइड किया जा सकता है।
- manufacturing आउटपुट अपडेट करने के लिए कारकस आकार बदलेंआवश्यकतानुसार कारकस आकार बदलें और manufacturing आउटपुट स्वचालित रूप से अपडेट हो जाते हैं।
- डिफ़ॉल्ट कारकस आकार बदलेंअपनी आवश्यकताओं के अनुसार डिफ़ॉल्ट कारकस आकार बदलें और manufacturing आउटपुट को स्वतः अपडेट होने दें।
- Choose the correct left or right end panel for a cabinetAdd a left or right end panel to a cabinet knowing that the side is decided by facing the shutters of the unit.
- extension पैरामीटर से skirting के gap को बंद करेंskirting कंपोनेंट पर extension पैरामीटर लागू करके skirting के gap को बंद करें।
- wardrobe पर front और back skirting कॉन्फ़िगर करेंचुनें कि wardrobe में front और back skirting है या नहीं।
- जिन carcass panel की आपको आवश्यकता नहीं है, उन्हें छिपाएँजिन carcass panel की आपको आवश्यकता नहीं है, उन्हें छिपाने के लिए panel visibility को टॉगल करें।
- उपकरण के आकार कारकस निर्माण को कैसे प्रभावित करते हैंजानें कि carcass panel के आकार कैसे गणना किए जाते हैं और उपकरण चुनने पर partition को उसमें फिट होने के लिए कैसे समायोजित किया जाता है।
- Carcass Panels Visibility में ग्रे किए गए Top स्विच को उपलब्ध करेंCarcass Panels Visibility में Top स्विच उपलब्ध होने के लिए Set Railing Options > Top > Type से 'Full' पर जाएँ, फिर top panel या front skirting panel हटाने के लिए visibility स्विच का उपयोग करें।
- cabinet level पर appliances के पीछे का back panel हटाएँAppliance unit में डिफ़ॉल्ट रूप से back panel नहीं होता, इसलिए उनके लिए कोई अतिरिक्त चरण आवश्यक नहीं है।
- rail-based back panel के लिए carcass back rail सेट करेंcarcass back rail विकल्प सेट करके कैबिनेट के back panel को पूरे panel के बजाय rail-based बनाएं।
- carcass panel thickness सेट करें और fillers को उससे मेल खाने के लिए बढ़ाएँअपने fillers को 18 mm carcass panel thickness के अनुसार मिलाएँ ताकि वे carcass के साथ समतल रहें।
- skirting joint order सेट करें और skirting को pricing से हटाएँचुनें कि skirting joint पर कौन सा panel top पर रहेगा, और जो skirting आप हटाते हैं उसे pricing quotation और BOQ से बाहर रखें।
- Snap lofts को carcass-to-carcass स्नैप करें, shutter-to-shutter नहींLoft unit को उनके shutter के बजाय उनके carcass से संरेखित करें, क्योंकि shutter के बीच 2 mm का gap होता है।
- अंतर्निहित carcass thickness पैरामीटर को समझेंजानें कि सॉफ़्टवेयर कौन से carcass thickness पैरामीटर स्वचालित रूप से बनाता है और कौन से आप स्वयं जोड़ते हैं।
- समझें कि carcass कॉन्फ़िगरेशन panel size को कैसे निर्धारित करता हैजानें कि panel size उसी carcass के अनुसार क्यों होता है जो वास्तव में बनाया गया है और ज़रूरत पड़ने पर thickness को कैसे समायोजित करें।
- sink unit के back panel और rails को समझेंजानें कि sink unit में पूरे back panel के बजाय पीछे की ओर rails डिफ़ॉल्ट होती हैं।
- समझें कि cabinet में carcass क्या होता हैजानें कि carcass में कौन से panel होते हैं और किसी भी cabinet type को बनाने के लिए इसे कैसे संशोधित किया जा सकता है।
- स्कर्टिंग ऊँचाई के अनुसार extension स्वतः बदलें, इसके लिए सूत्रों का उपयोग करेंextension के मान को स्कर्टिंग ऊँचाई का संदर्भ देने वाले सूत्र से नियंत्रित करें, ताकि वह ऊँचाई बदलने पर स्वयं अपडेट हो जाए।
- कैबिनेट निर्माण, स्कर्टिंग, काउंटरटॉप और carcass panel को अनुकूलित करेंचयनित कैबिनेट पर customize टैब खोलकर उसका निर्माण, स्कर्टिंग, काउंटरटॉप और carcass panel सेट करें।
- कस्टम support panel जोड़ें और back panel offset तथा grooving सेट करेंअपने core material, finish और label वाला support panel जोड़ें, और extension parameters में back panel offset तथा grooving depth कॉन्फ़िगर करें।
- cabinet स्तर पर shutter और carcass finish तथा core सेट करेंproperties panel से shutter और carcass finish तथा core material चुनें, ताकि inheriting shutter cabinet का अनुसरण करें।
- shutter, skirting और carcass dimension का हिसाब रखेंpanel size को shutter thickness, skirting buffer और drawer clearance के लिए समायोजित करें, जिन्हें carcass के आंकड़े छोड़ देते हैं।
- shutter और carcass material thickness तथा finishes को अलग-अलग कॉन्फ़िगर करेंcarcass और shutter के लिए core material और finish स्वतंत्र रूप से सेट करें, ताकि प्रत्येक घटक का अपना चयन रहे।
- skirting दिखाने के बजाय panel को floor तक नीचे बढ़ाएँpanel की construction settings में extension parameters का उपयोग करके panel को skirting दिखाने के बजाय floor तक जारी रखें।
- back panel से बाहर निकलने वाले drawer को ठीक करेंउपयोग योग्य cabinet गहराई से मेल खाने वाला channel चुनकर back panel से बाहर निकल रहे drawer को ठीक करें।
- carcass panel और shutter panel के लिए hinge की मात्रा कैसे जनरेट होती हैजानें कि hinge की गिनती carcass panel और shutter panel के बीच इंटरैक्शन से क्यों होती है, और जब carcass panel बंद होता है तो क्या होता है।
- shutter और carcass core material तथा thickness सेट करेंshutter और carcass के लिए BWP, BW या HDMR जैसा core material चुनें और प्रत्येक की thickness दें; back panel डिफ़ॉल्ट रूप से 6 mm standard material रहता है।
- Add hardware में custom panel carcass joint जोड़नाcustom panel के बीच carcass-to-carcass जंक्शन पर connector और हार्डवेयर मैन्युअल रूप से जोड़ें।
- wardrobe की construction को मैन्युअली बदलें और back skirting बंद करेंsliding wardrobe के लिए उसकी construction को मैन्युअली बदलकर और back skirting बंद करके wardrobe को कस्टमाइज़ करें।
- drawer height, front panel reduction और carcass 1mm reduction सेट करेंआवश्यक heights के साथ drawer settings structure और drawer-level construction कॉन्फ़िगर करें, फिर drawer level पर front panel reduction सेट करें।
- drawer system में custom panel जोड़ें और उन्हें carcass material के रूप में map करेंdrawer system level पर custom panel जोड़ें और किसी भी panel level पर उनका material सेट करें ताकि उन्हें carcass material के रूप में map किया जा सके।
- खाली carcass से wardrobe internals स्वयं बनाएँcatalogue से एक wardrobe विकल्प रखें और shelves तथा vertical panels या तैयार partition configuration का उपयोग करके उसके internals स्वयं बनाएँ।
- कार्कस से shutter तक मापने के लिए मैन्युअल डाइमेंशनिंग हेतु shutter panel सक्षम करेंfloor plan में मैन्युअल डाइमेंशनिंग के लिए panel सक्षम करके और shutter panel चुनकर कार्कस से shutter तक मापें।
- Construction level पर back panel को बढ़ाएँback panel को बढ़ाने के लिए Construction level पर जाएँ।
- carcass panel निर्माण के साथ wardrobe संरचना कॉन्फ़िगर करेंwardrobe संरचना कॉन्फ़िगर करने और vertical panel तथा drawer जैसे आंतरिक और बाहरी घटक जोड़ने के लिए carcass panel निर्माण अनुभाग का उपयोग करें।
- end panel को floor या ceiling तक बढ़ाएँकिसी cabinet के End Panel section से जोड़े गए end panel को Width Extension मानों का उपयोग करके नीचे floor तक या उसके अपने panel से ऊपर की ओर बढ़ाएँ।
- bottom panel को बढ़ाकर उस gap को ढकें जहाँ skirting टूटती हैpanel चुनें और इसे बढ़ाकर उस gap को ढकें जहाँ अन्यथा अलग skirting टूट जाती।
- drawer फिनिश carcass finish को कैसे विरासत में लेती हैंजानें कि drawer फिनिश carcass internal और external finish का पालन कैसे करती हैं, जब तक आप उन्हें drawer system स्तर पर स्पष्ट रूप से न बदलें।
- wardrobe construction style कैसे carcass parameters संग्रहीत करता हैजानें कि wardrobe unit construction style कौन-से carcass parameters रखता है और style को अपडेट करने पर वे wardrobe पर कैसे लागू होते हैं।
- carcass panel thickness का उपयोग करके bottom panel को अंदर की ओर offset करेंbottom panel को एक panel thickness ऊपर उठाएँ ताकि वह side panel के नीचे के बजाय carcass के अंदर बैठे।
- back panel वाले carcass में फिट होने के लिए drawer का साइज़ निर्धारित करेंcarcass की उपयोगी आंतरिक गहराई निकालें, ताकि drawer back panel से टकराए बिना फिट हो जाए।
- wardrobe skirting construction में front panel और side panel को समझेंजानें कि wardrobe skirting construction में front panel और side panel कैसे बनाए जाते हैं।
- sink unit rails और skirting विकल्पों को समझेंजानें कि sink unit, top और back rails के साथ कैसे बनते हैं और cabinet skirting विकल्पों से skirting को कैसे चालू या बंद करें।
- panel-level visibility से carcass panel छिपाएँ या हटाएँcabinet के Construction > Carcass > Carcass Panels Visibility से एक single carcass panel बंद करें।
- कारकस width और thickness से sized एक custom horizontal panel जोड़ेंकैबिनेट के अंदर एक horizontal custom panel जोड़ें और इसे carcass width, depth और panel thickness से size करें ताकि यह सही ढंग से align हो।
- split skirting segments को panel type असाइन करेंsplit skirting segments को वे panel type दें जिनसे hardware और connector नियम उन्हें unsplit skirting से अलग पहचान सकें।
- ऐसे panel खोजें जो carcass material का पालन नहीं करतेcore section के अंतर्गत custom core property देखकर ऐसे panel पहचानें जिनका custom core material carcass का पालन नहीं करता।
- फिनिश श्रेणियाँ shutter और carcass की सतहों को कैसे नियंत्रित करती हैंजानें कि चार फिनिश श्रेणियाँ यह कैसे तय करती हैं कि फिनिश panel की किस सतह पर लगेगी और सही चयन क्यों महत्वपूर्ण है।
- skirting hardware rule किस प्रकार प्रति SKU skirting लंबाई को एकत्रित करते हैंजानें कि स्वचालित hardware rule के लिए सिस्टम पूरे floor पर प्रति skirting SKU skirting लंबाई का योग कैसे करता है।
- Shelf reveal और back panel grooving मानों को presets के रूप में सेट करेंअपने account में shelf reveal और back panel grooving मानों को presets के रूप में कॉन्फ़िगर करें, ताकि आपको हर design के लिए उन्हें बार-बार बदलना न पड़े।
- Quick Access से shutter और carcass core material तथा thickness सेट करेंQuick Access से shutter और carcass core material तथा उसकी thickness सेट करें।
- Carcass के अंदर partition offset दूरी सेट करेंजानें कि carcass के अंदर partition जोड़ते समय partition offset मान का क्या अर्थ है, ताकि आप partition की thickness सेट करने के बजाय उसे एक दूरी से inset करें।
- व्यापक carcass panel के बजाय विशिष्ट panel लक्षित करेंकिसी नियम की panel-type शर्त को सीमित करें ताकि connector केवल उन्हीं panel पर लगें जिन्हें आप चाहते हैं।
- समझें कि फ्लोरप्लान में फिलर कैबिनेट कारकास बॉक्स क्यों दिखाते हैंजानें कि प्लान में फिलर कैबिनेट बॉक्स के रूप में क्यों दिखता है और उस बॉक्स का आकार क्या दर्शाता है।
और गाइड 3
सभी दिखाएँ (3)
- Minifix और dowel की नियुक्ति कैसे स्वचालित होती हैजानें कि कारकास में Minifix और dowel की स्वचालित नियुक्ति किस आधार पर होती है।
- स्टोरेज बॉक्स का आंतरिक और बाहरी रंग बदलेंसंबंधित रंग नियंत्रणों का उपयोग करके स्टोरेज बॉक्स का कारकस रंग और external finish स्वतंत्र रूप से सेट करें।
- खाता डिफ़ॉल्ट से निर्माण मान कैसे आते हैंस्कर्टिंग और अन्य निर्माण मान आपके खाते की डिफ़ॉल्ट सेटिंग्स से भरे जाते हैं।