벽
가이드: 72
- 벽 도구에서 곡선 벽 만들기벽 드롭다운에서 곡선 벽 옵션을 선택해 곡선 벽을 그린 다음, 반지름과 기타 속성을 세밀하게 조정하세요.
- 천장 높이에서 벽 높이와 슬래브 두께 설정천장의 높이를 읽고 같은 패널에서 슬래브 두께를 설정하여 주방 배치에 맞는 올바른 벽 높이를 정합니다.
- 문과 창문을 추가하기 전에 벽 높이와 두께를 설정하세요벽 높이와 두께를 설정한 다음, 높이, 너비, 두께, 높낮이로 문과 창문을 정의하세요.
- 벽걸이장에는 베이스 프로파일이 아닌 벽걸이 골라 프로파일을 사용하십시오.벽걸이장에 골라 프로파일을 추가할 때는 벽걸이 골라 프로파일을 선택하십시오. 베이스 프로파일은 벽걸이장에 맞지 않습니다.
- Close walls into a room and edit wall propertiesClose walls into a room, name it, and adjust wall height and thickness from the properties panel.
- Create and open a wall section elevation from a wall face in 3DClick a wall's face in 3D to select that wall section, then add an elevation of that face and open it from the Wall Section Elevation list.
- Fix a disabled wall tool when drawing wallsSwitch to the floor level and 2D floor plan so the wall tool becomes available again.
- Fix two separate walls that cannot be mergedDelete one of the two walls and trim or extend the remaining wall so it spans the full run.
- Set the default wall elevation view distance for your organisationSet the distance used when opening a wall elevation view once as an organisation-wide default instead of changing it per view.
- Understand the wall location line and how typed dimensions are measuredLearn how the location line places wall thickness and which face your typed dimensions are measured from.
- Add base, wall and tall units from the kitchen furniture catalogMark the room as a kitchen so the base, wall and tall units under kitchen furniture in Insert / Furnish are easier to access.
- Add base, wall, tall and loft fillers from the kitchen fillers libraryPlace base, wall unit, wall, tall unit and loft fillers in your kitchen design the same way you place cabinets.
- 벽 마감 재료로 벽지 또는 페인트 추가벽의 마감 재료 옵션에서 선택하여 벽에 벽지 또는 페인트 마감을 적용하세요.
- Build layered custom wall designs with tiling and fixed-distance copyCreate a custom wall design such as a rafter by building each layer from a rectangle with its own dimensions and extrude depth.
- Change a wall's length by editing its dimension valueSelect a wall and type a new dimension value to redraw it as a straight wall at the length you set.
- Change wall, door and window properties from the Modify menuAdjust wall dimensions and colours, door and window sizes, window height and elevation, and swap window models from the Modify menu.
- 타일링 및 절단 도구를 사용하여 벽에 다도를 만들기벽 표면에 닫힌 다도 윤곽을 그리면 타일링 및 절단 도구가 이를 다도로 적용합니다.
- Tab으로 스냅 후보를 순환하고 벽을 선택하세요그리는 동안 Tab과 Shift+Tab으로 스냅 후보를 순환하고, 선택된 벽에서 Tab을 누르면 방 전체 외곽선을 잡을 수 있습니다.
- Cycle wall location line, staircase side and window position with SpacebarPress the spacebar while drawing or moving walls, staircases and windows to cycle their location line, drawing side or position.
- 벽을 끊김 없는 전체 구간으로 그리고 벽 중앙에 문을 배치하세요각 벽을 하나의 끊김 없는 구간으로 그리고 벽 중앙에 스냅하여 그 위에 문을 배치하세요.
- Draw a wall at an exact length and chain the next wallPoint in the wall's direction, type its length to open a length box, and press Enter so the wall is drawn at exactly that length and the next wall starts from its end.
- Draw a wall from start point to end pointClick the wall's start point, then set its end point by clicking the canvas or typing a length, and close a room by returning to the first start point.
- Arc Drawing 모드로 곡선 벽 그리기Draw by Bending, Draw around Center 또는 Draw along Tangent를 사용하여 곡선 벽을 그리고, 벽의 왼쪽 패널에서 반지름을 조정하세요.
- 바닥 레벨에서 벽과 평면도를 그립니다벽과 평면도를 어느 레벨에서 그려야 하는지, 그리고 인테리어 작업 시 어떤 레벨 사이를 이동하는지 알아봅니다.
- Draw walls in the 2D floor plan with exact dimensionsDraw walls in the 2D floor plan by entering height and thickness, then clicking and typing exact lengths.
- Edit wall interiors at room levelWork on the interiors of the wall at room level, rotate the room and view the wall height.
- AI 평면도에서 누락된 짧은 벽과 발코니 수정평면도를 생성한 후 AI가 감지하지 못한 짧은 벽과 발코니를 추가하거나 수정하세요.
- 허용되는 최소 벽 길이는 100 mm입니다벽 도구로 벽을 그릴 때 시스템이 허용하는 가장 짧은 벽은 100 mm입니다.
- Front Shift을(를) 사용하여 벽 디자인을 벽에서 떨어뜨리기타일링-컷팅 도형에 Front Shift을(를) 설정하여 벽면에 부착된 디자인을 프로젝트 단위의 값만큼 벽 표면 앞으로 이동합니다.
- Move or resize a wall with the circular end handleClick the circular handle at one end of a wall and drag it to shorten, extend or reposition the wall.
- Place openings away from walls, then set exact distance by typingMove an opening clear of the wall in 2D and then type its exact distance instead of dragging it.
- Set the wall location line to match the dimension typeMatch the wall location line to the dimension you need so outer-to-outer, inner-to-inner and centre-to-centre values measure from the intended face.
- 프리셋 또는 사용자 지정 값으로 벽 두께 설정카탈로그의 프리셋 옵션에서 벽의 마감 재료 두께를 선택하거나 사용자 지정 값을 직접 입력하세요.
- 요소를 배치할 때 벽 중심 표시기를 확인하세요커서가 벽의 정확한 중심에 도달하면 분홍색 십자가 분홍색 삼각형으로 바뀌고, 벗어나면 다시 십자가로 돌아오는 것을 확인하세요.
- 바닥 배경으로 추가한 DWG 또는 축척이 지정된 이미지 위에 벽을 그립니다DWG 파일 또는 축척이 지정된 이미지를 바닥 그리기 배경으로 추가한 다음, 건축 벽 도구로 그 위에 벽을 그립니다.
- Understand why imported 3D models cannot be edited like native wallsLearn why a 3D model built outside Infernia is not recognised as a native Infernia wall and cannot be edited the same way.
- 벽을 그리는 동안 스페이스바를 사용하여 방향을 고정하세요시작점에서 직선 벽을 그리고 이동하면서 내부 치수를 확인한 후 확정하세요.
- Use the pick tool to select internal wall faces for ceilings and tilingPick internal wall faces to sketch a ceiling and apply tiling, then adjust tile material, pattern, size and grout appearance room by room.
- 문의 열림 방향과 경첩을 뒤집고 벽으로부터의 거리를 설정합니다배치된 문을 선택하여 문이 열리는 방향과 경첩 위치를 바꾸려면 해당 면이나 경첩을 뒤집으세요.
- 3D 벽에서 입면도를 생성하고 리치 뷰 또는 스켈레톤 뷰로 전환하세요3D 뷰에서 벽을 선택해 입면도를 생성한 다음, 리치 뷰와 스켈레톤 뷰 및 기타 표시 모드 사이를 전환하세요.
- 방 템플릿으로 디자인을 시작하고 벽 크기를 조정하기미리 만들어진 방이 포함된 방 템플릿으로 새 디자인을 시작한 다음, 벽을 선택하고 치수를 변경하여 크기를 조정하세요.
- 벽 섹션과 검색을 통해 벽에 걸레받이 추가내부 벽에 벽 걸레받이를 켜고 검색으로 원하는 걸레받이 베이스를 찾으세요.
- 벽에 걸레받이 추가벽을 선택하고 wall skirting을 켜서 걸레받이를 추가하세요.
- 벽 섹션의 속성 패널에서 벽 걸레받이를 적용합니다벽 섹션의 속성 패널에서 Wall Skirting을(를) 켜고 벽에 적용할 걸레받이 마감을 선택하세요.
- 너비, 높이, 두께 및 벽 거리를 사용하여 문 추가 및 편집평면도에서 벽에 문을 배치하고, 크기와 벽으로부터의 거리를 설정하며, 모델과 재질을 변경합니다.
- 벽 두께를 관통하도록 돌출하여 문 또는 창 컷아웃 만들기벽에 문 또는 창을 위한 개구부를 만들려면 컷 영역을 그리고 벽 두께를 관통하도록 돌출합니다.
- 벽 틈 없이 방 모서리에서 천장을 그립니다천장 명령 메뉴에서 사각형을 그려 천장을 추가한 다음, 같은 방법으로 타일링을 추가합니다.
- 벽 표면을 클릭하여 입면도를 생성하세요벽의 표면을 클릭하면 입면도가 흑백 또는 컬러로 자동 생성됩니다.
- 평면도에서 천장을 추가하고 입면을 벽 높이에 맞춥니다평면도 보기에서 ceiling 옵션을 선택하고 실내에 적용하여 천장을 추가합니다.
- 벽을 선택하고 타일링 도구를 사용하여 벽 타일링을 추가하세요벽을 선택하고 타일링 및 절단 도구로 타일 영역을 그려 벽에 타일링을 추가하세요.
- Build a TV unit from modular base, wall and open unitsOpen the Furnish panel, choose multi-purpose modular furniture, and combine, rotate and position units to compose a TV unit.
- 창을 중앙에 배치하고 벽 간격을 정확히 설정창을 벽 중앙에 배치하고 벽으로부터의 거리를 정확히 지정합니다.
- 핵심 설계 단계: 벽, 문, 창, 천장 및 타일링벽을 그리고 문을 추가하고 창을 추가하고 천장을 추가하고 타일링을 추가하여 설계를 완성합니다.
- Create a room by adding walls, openings, ceiling and tiles in sequenceClose the walls fully so the ceiling tool detects the room area and measures the ceiling automatically, then view and edit the room in 3D.
- Create a room by closing all walls into a loopClose all wall segments into a fully closed loop without overlapping boundary lines so the software generates the room automatically.
- Move a door or window to an exact distance from the wall sidePlace an opening centered on a wall, then use its side dimensions to set the exact distance from either side.
- Front shift로 파티션과 패턴을 벽에서 앞으로 오프셋하세요벽에서 앞으로 오프셋을 설정하여 파티션, 서까래 및 그려진 패턴이 원하는 거리에 위치하도록 하세요.
- 폴 천장의 표고를 벽 높이에서 천장 두께를 뺀 값으로 설정폴 천장의 형상과 두께를 정의한 다음, 표고를 벽 높이에서 천장 두께를 뺀 값으로 설정하여 천장이 벽 상단 아래에 올바르게 위치하도록 합니다.
- Turn on auto snapping to constrain walls to 90 degreesTurn on Orthogonal Snapping so the walls and lines you draw stay at 90 degrees, then join walls with Trim/Extend to Corner.
- Add a door to a wallPlace a door on a wall from the Architecture or Home tab and set it up in the Door panel.
- Sweep Tool로 코니스, 몰딩 및 벽 패널을 추가하세요벽에 Sweep Tool을 사용하여 사용자 지정 코니스, 몰딩 및 장식용 벽 패널을 추가하고, 타일 절단의 스윕 모드를 사용하여 벽 몰딩과 셔터 디자인을 만드세요.
- Create and edit rooms from enclosed wallsEnclose four walls to get an automatic floor and room text, then rename the room and change its text properties.
- How ceilings and floors reference wallsLearn that a ceiling and floor in the design module can be created using a wall as a reference.
- Place doors after walls and edit size, height, thickness, hinge and modelAdd doors after your walls are ready, then adjust each door's size, orientation and model so it looks right in 3D.
- Set default door, window and wall properties via PreferencesSet default properties for repeated elements so newly added doors, windows, elevations and walls inherit the same values across all rooms.
- Set room dimensions from center or inner walls and pick room typeSwitch room dimensions to inner-wall measurements and choose a room type so Insert and Furnish only offers matching furniture and accessories.
- Set room inner dimensions and wall height before designingSet the left wall height and thickness and name the room so it is identifiable in the project before you start designing.
- 드래그한 창이 벽 중앙에 정렬되는 시점 확인선택한 창을 벽을 따라 드래그하고 분홍색 표시를 확인하여 창이 중앙에 정렬되는 시점을 파악하세요.
- Trim an extra wall or room-divider segmentRemove an extra wall or room-divider segment using the trim shortcut T R or the trim option in the on-screen menu.
- 키보드 단축키로 벽, 가구 및 타일링 추가짧은 코드를 입력하고 Enter를 눌러 가구 추가, 벽 그리기, 타일링 추가, 문 배치와 같은 일반 명령을 실행하세요.