বেৰ
গাইড: 72
- ৱালছ সঁজুলিৰ পৰা বক্ৰ দেৱাল সৃষ্টি কৰকবক্ৰ দেৱাল আঁকিবলৈ ৱালছ ড্ৰপডাউনত বক্ৰ দেৱালৰ বিকল্প বাছনি কৰক, তাৰ পিছত ইয়াৰ ৰেডিয়াছ আৰু অন্যান্য বৈশিষ্ট্য সূক্ষ্মভাৱে সমন্বয় কৰক।
- চিলিংৰ উচ্চতাৰ পৰা বেৰৰ উচ্চতা আৰু স্লেবৰ বেধ নিৰ্ধাৰণ কৰকচিলিংৰ উচ্চতা পঢ়ি আৰু একেটা পেনেলৰ পৰা স্লেবৰ বেধ নিৰ্ধাৰণ কৰি ৰান্ধনীঘৰৰ বিন্যাসৰ বাবে সঠিক বেৰৰ উচ্চতা স্থাপন কৰক।
- দুৱাৰ আৰু খিৰিকী যোগ কৰাৰ আগতে বেৰৰ উচ্চতা আৰু ডাঠতা নিৰ্ধাৰণ কৰকবেৰৰ উচ্চতা আৰু ডাঠতা নিৰ্ধাৰণ কৰক, তাৰ পিছত দুৱাৰ আৰু খিৰিকীৰ উচ্চতা, প্ৰস্থ, ডাঠতা আৰু উচ্চতা (elevation)ৰ দ্বাৰা সিহঁতক নিৰ্ধাৰণ কৰক।
- ৱাল ইউনিটৰ বাবে ৱাল গোলা প্ৰফাইল ব্যৱহাৰ কৰক, বেছ প্ৰফাইল নহয়ৱাল কেবিনেটত গোলা প্ৰফাইল যোগ কৰোঁতে ৱাল গোলা প্ৰফাইল বাছনি কৰক, কাৰণ ৱাল ইউনিটৰ বাবে বেছ প্ৰফাইল অনুপযুক্ত।
- Close walls into a room and edit wall propertiesClose walls into a room, name it, and adjust wall height and thickness from the properties panel.
- Create and open a wall section elevation from a wall face in 3DClick a wall's face in 3D to select that wall section, then add an elevation of that face and open it from the Wall Section Elevation list.
- Fix a disabled wall tool when drawing wallsSwitch to the floor level and 2D floor plan so the wall tool becomes available again.
- Fix two separate walls that cannot be mergedDelete one of the two walls and trim or extend the remaining wall so it spans the full run.
- Set the default wall elevation view distance for your organisationSet the distance used when opening a wall elevation view once as an organisation-wide default instead of changing it per view.
- Understand the wall location line and how typed dimensions are measuredLearn how the location line places wall thickness and which face your typed dimensions are measured from.
- Add base, wall and tall units from the kitchen furniture catalogMark the room as a kitchen so the base, wall and tall units under kitchen furniture in Insert / Furnish are easier to access.
- Add base, wall, tall and loft fillers from the kitchen fillers libraryPlace base, wall unit, wall, tall unit and loft fillers in your kitchen design the same way you place cabinets.
- ৱাল ফিনিছ মেটেৰিয়েলৰ জৰিয়তে ৱালপেপাৰ বা পেইণ্ট যোগ কৰকৱালৰ ফিনিছ মেটেৰিয়েলৰ বিকল্পসমূহৰ পৰা বাছনি কৰি এখন ৱালত ৱালপেপাৰ বা পেইণ্ট ফিনিছ দিয়ক।
- Build layered custom wall designs with tiling and fixed-distance copyCreate a custom wall design such as a rafter by building each layer from a rectangle with its own dimensions and extrude depth.
- Change a wall's length by editing its dimension valueSelect a wall and type a new dimension value to redraw it as a straight wall at the length you set.
- Change wall, door and window properties from the Modify menuAdjust wall dimensions and colours, door and window sizes, window height and elevation, and swap window models from the Modify menu.
- টাইলিং আৰু কাটিং সঁজুলি ব্যৱহাৰ কৰি বেৰত এটা ডেডো সৃষ্টি কৰকবেৰৰ পৃষ্ঠত এটা বন্ধ ডেডো আউটলাইন আঁকক যাতে টাইলিং আৰু কাটিং সঁজুলিয়ে ইয়াক ডেডো হিচাপে প্ৰয়োগ কৰে।
- Tab ৰ সৈতে snap প্ৰাৰ্থীসমূহ চক্ৰ কৰক আৰু দেৱাল নিৰ্বাচন কৰকআঁকোতে snap প্ৰাৰ্থীসমূহ চক্ৰ কৰিবলৈ Tab আৰু Shift+Tab ব্যৱহাৰ কৰক, আৰু নিৰ্বাচিত দেৱালত Tab টিপি গোটেই ৰুমৰ আউটলাইন লওক।
- Cycle wall location line, staircase side and window position with SpacebarPress the spacebar while drawing or moving walls, staircases and windows to cycle their location line, drawing side or position.
- দেৱালসমূহক সম্পূৰ্ণ অবিচ্ছিন্ন ৰান হিচাপে খচৰা কৰক আৰু দুৱাৰসমূহ দেৱালৰ কেন্দ্ৰত স্থাপন কৰকপ্ৰতিখন দেৱাল এখন অবিচ্ছিন্ন ৰান হিচাপে আঁকক আৰু দেৱালৰ কেন্দ্ৰলৈ স্নেপ কৰি তাৰ ওপৰত দুৱাৰ স্থাপন কৰক।
- Draw a wall at an exact length and chain the next wallPoint in the wall's direction, type its length to open a length box, and press Enter so the wall is drawn at exactly that length and the next wall starts from its end.
- Draw a wall from start point to end pointClick the wall's start point, then set its end point by clicking the canvas or typing a length, and close a room by returning to the first start point.
- Arc Drawing ম'ডত বক্ৰ দেৱাল আঁককDraw by Bending, Draw around Center বা Draw along Tangent ব্যৱহাৰ কৰি বক্ৰ দেৱাল আঁকক, আৰু দেৱালৰ বাওঁ পেনেলৰ পৰা ৰেডিয়াছ সমন্বয় কৰক।
- মজিয়াৰ স্তৰত বেৰ আৰু মজিয়াৰ পৰিকল্পনা অঁকাকোনটো স্তৰত বেৰ আৰু মজিয়াৰ পৰিকল্পনা অঁকিব লাগে, আৰু আভ্যন্তৰীণ কামৰ বাবে কোনবোৰ স্তৰৰ মাজত আপুনি চলাচল কৰে, সেয়া শিকক।
- Draw walls in the 2D floor plan with exact dimensionsDraw walls in the 2D floor plan by entering height and thickness, then clicking and typing exact lengths.
- Edit wall interiors at room levelWork on the interiors of the wall at room level, rotate the room and view the wall height.
- AI ফ্ল'ৰপ্লেনে মিছ কৰা চুটি দেৱাল আৰু বাৰাণ্ডা ঠিক কৰকপ্লেন সৃষ্টি কৰাৰ পিছত, AI-এ চিনাক্ত নকৰা চুটি দেৱাল আৰু বাৰাণ্ডা যোগ কৰক বা শুধৰাই দিয়ক।
- অনুমোদিত ন্যূনতম ৱালৰ দৈৰ্ঘ্য 100 mmৱাল সঁজুলিৰে ৱাল আঁকোতে, ছিষ্টেমে গ্ৰহণ কৰা আটাইতকৈ চুটি ৱালৰ দৈৰ্ঘ্য 100 mm।
- Front Shift ৰ সৈতে এখন দেৱাল ডিজাইন দেৱালৰ পৰা আঁতৰাই লৈ যাওকআপোনাৰ প্ৰজেক্টৰ এককত এটা মানৰ দ্বাৰা দেৱালত লগোৱা ডিজাইন দেৱালৰ পৃষ্ঠৰ পৰা আগলৈ লৈ যাবলৈ টাইলিং-কাটিং শ্বেপত Front Shift ছেট কৰক।
- Move or resize a wall with the circular end handleClick the circular handle at one end of a wall and drag it to shorten, extend or reposition the wall.
- Place openings away from walls, then set exact distance by typingMove an opening clear of the wall in 2D and then type its exact distance instead of dragging it.
- Set the wall location line to match the dimension typeMatch the wall location line to the dimension you need so outer-to-outer, inner-to-inner and centre-to-centre values measure from the intended face.
- প্ৰিছেট বা কাষ্টম মানৰ পৰা ৱালৰ বেধ নিৰ্ধাৰণ কৰকপ্ৰিছেট কেটেলগৰ বিকল্পসমূহৰ পৰা ৱালৰ সমাপ্ত সামগ্ৰীৰ বেধ বাছনি কৰক বা নিজৰ কাষ্টম মান টাইপ কৰক।
- কোনো উপাদান স্থাপন কৰি থকাৰ সময়ত ৱাল চেণ্টাৰ ইণ্ডিকেটৰ চিনি পাওককাৰ্ছৰ ৱালৰ সঠিক কেন্দ্ৰত উপনীত হ'লে গোলাপী ক্ৰছটো গোলাপী ত্ৰিভুজলৈ পৰিৱৰ্তিত হয় আৰু আঁতৰি গ'লে পুনৰ আগৰ ৰূপলৈ ঘূৰি আহে, তাক লক্ষ্য কৰক।
- মজিয়াৰ পটভূমি হিচাপে যোগ কৰা DWG বা স্কেল কৰা ছবিৰ ওপৰত দেৱাল ট্ৰেছ কৰকমজিয়া ট্ৰেছ কৰাৰ পটভূমি হিচাপে DWG ফাইল বা স্কেল কৰা ছবি যোগ কৰক, তাৰ পিছত স্থাপত্যৰ দেৱাল সঁজুলিৰে ইয়াৰ ওপৰত দেৱাল ট্ৰেছ কৰক।
- Understand why imported 3D models cannot be edited like native wallsLearn why a 3D model built outside Infernia is not recognised as a native Infernia wall and cannot be edited the same way.
- দেৱাল অঁকাৰ সময়ত দিশ লক কৰিবলৈ spacebar ব্যৱহাৰ কৰকএটা আৰম্ভণি বিন্দুৰ পৰা পোন দেৱাল অঁকক আৰু চূড়ান্ত কৰাৰ আগতে আগবাঢ়ি যোৱাৰ সময়ত ইয়াৰ আভ্যন্তৰীণ জোখ পৰীক্ষা কৰক।
- Use the pick tool to select internal wall faces for ceilings and tilingPick internal wall faces to sketch a ceiling and apply tiling, then adjust tile material, pattern, size and grout appearance room by room.
- দুৱাৰৰ swing আৰু hinge flip কৰক, আৰু বেৰৰ পৰা দূৰত্ব নিৰ্ধাৰণ কৰকএখন স্থাপন কৰা দুৱাৰ বাছনি কৰি ইয়াৰ কাষ বা hinge flip কৰক, যাতে ই কোনফালে খোলে আৰু ক'ত hinge কৰা আছে সেয়া সলনি হয়।
- Create elevations from a 3D wall and toggle rich or skeleton viewGenerate an elevation from a wall in the 3D view, then switch between rich view and skeleton view and other display modes.
- কক্ষৰ টেমপ্লেটৰ পৰা এটা ডিজাইন আৰম্ভ কৰক আৰু ইয়াৰ বেৰবোৰৰ আকাৰ সলনি কৰককক্ষৰ টেমপ্লেটৰ পৰা এটা নতুন ডিজাইন আৰম্ভ কৰক, য'ত আগতেই সৃষ্টি কৰা এটা কক্ষ থাকে; তাৰ পিছত বেৰ বাছনি কৰি আৰু সিহঁতৰ জোখ সলনি কৰি ইয়াৰ আকাৰ সলনি কৰক।
- ৱাল ছেকচন আৰু সন্ধানৰ জৰিয়তে দেৱালত স্কাৰ্টিং যোগ কৰকআপোনাৰ ভিতৰৰ দেৱালৰ বাবে ৱাল স্কাৰ্টিং অন কৰক আৰু সন্ধান কৰি আপুনি বিচৰা স্কাৰ্টিং বেছ বিচাৰি উলিয়াওক।
- দেৱালত দেৱাল স্কাৰ্টিং যোগ কৰকএখন দেৱাল বাছনি কৰক আৰু তাত স্কাৰ্টিং যোগ কৰিবলৈ দেৱাল স্কাৰ্টিং অন কৰক।
- ৱাল ছেক্সনৰ প্ৰপাৰ্টিজ পেনেলৰ পৰা ৱাল স্কাৰ্টিং প্ৰয়োগ কৰকৱাল ছেক্সনৰ প্ৰপাৰ্টিজ পেনেলত Wall Skirting অন কৰক আৰু ৱালত প্ৰয়োগ কৰিবলৈ স্কাৰ্টিং ফিনিছ বাছনি কৰক।
- প্ৰস্থ, উচ্চতা, বেধ আৰু ৱালৰ পৰা দূৰত্বৰ সৈতে দুৱাৰ যোগ কৰক আৰু সম্পাদনা কৰকফ্ল'ৰ প্লেনত এখন ৱালত দুৱাৰ স্থাপন কৰক, ইয়াৰ আকাৰ আৰু ৱালৰ পৰা দূৰত্ব নিৰ্ধাৰণ কৰক, আৰু ইয়াৰ মডেল আৰু মেটেৰিয়েল সলনি কৰক।
- দেৱালৰ বেধৰ মাজেৰে এক্সট্ৰুড কৰি দুৱাৰ বা খিৰিকিৰ কাটআউট সৃষ্টি কৰককাটা অংশ অংকন কৰি আৰু দেৱালৰ বেধৰ মাজেৰে এক্সট্ৰুড কৰি দেৱালত দুৱাৰ বা খিৰিকিৰ বাবে এটা খোলা কাটক।
- প্ৰতিটো ৰুমৰ চুকৰ পৰা বেৰৰ ফাঁক নোহোৱাকৈ চিলিং আঁককচিলিং কমাণ্ড মেনুৰ পৰা এটা আয়তক্ষেত্ৰ আঁকি চিলিং যোগ কৰক, তাৰ পিছত একে ধৰণেৰে টাইলিং যোগ কৰক।
- দেৱালৰ পৃষ্ঠত ক্লিক কৰি এটা elevation সৃষ্টি কৰকতাৰ elevation স্বয়ংক্ৰিয়ভাৱে সৃষ্টি কৰিবলৈ দেৱালৰ পৃষ্ঠত ক্লিক কৰক, ক'লা-বগা বা ৰঙীন।
- মজিয়াৰ প্লেনৰ পৰা চিলিং যোগ কৰক আৰু এলিভেচনক ৱালৰ উচ্চতাৰ সৈতে মিলাওকমজিয়াৰ প্লেন দৃশ্যত চিলিং বিকল্প বাছনি কৰি আৰু কোঠাটোৰ ভিতৰত প্ৰয়োগ কৰি এটা চিলিং যোগ কৰক।
- বেৰ বাছনি কৰি আৰু টাইলিং সঁজুলি ব্যৱহাৰ কৰি বেৰৰ টাইলিং যোগ কৰকবেৰ বাছনি কৰি আৰু টাইলিং আৰু কাটিং সঁজুলিৰে টাইলযুক্ত অঞ্চল অঁকি বেৰত টাইলিং যোগ কৰক।
- Build a TV unit from modular base, wall and open unitsOpen the Furnish panel, choose multi-purpose modular furniture, and combine, rotate and position units to compose a TV unit.
- এখন ৱিণ্ডো কেন্দ্ৰত ৰাখক আৰু দেৱালৰ সঠিক ব্যৱধান নিৰ্ধাৰণ কৰকএখন ৱিণ্ডো দেৱালৰ মাজত ৰাখক আৰু দেৱালৰ পৰা ইয়াৰ সঠিক দূৰত্ব নিৰ্ধাৰণ কৰক।
- মূল ডিজাইন পদক্ষেপসমূহ: ৱাল, দুৱাৰ, খিৰিকী, চিলিং আৰু টাইলিংএটা ডিজাইন সম্পূৰ্ণ কৰিবলৈ ৱাল আঁকক, দুৱাৰ যোগ কৰক, খিৰিকী যোগ কৰক, চিলিং যোগ কৰক আৰু টাইলিং যোগ কৰক।
- Create a room by adding walls, openings, ceiling and tiles in sequenceClose the walls fully so the ceiling tool detects the room area and measures the ceiling automatically, then view and edit the room in 3D.
- Create a room by closing all walls into a loopClose all wall segments into a fully closed loop without overlapping boundary lines so the software generates the room automatically.
- Move a door or window to an exact distance from the wall sidePlace an opening centered on a wall, then use its side dimensions to set the exact distance from either side.
- Front shift ৰ সৈতে ৱালৰ পৰা আগলৈ পাৰ্টিশ্বন আৰু পেটাৰ্ন অফছেট কৰকৱালৰ পৰা এটা আগলৈ অফছেট নিৰ্ধাৰণ কৰক যাতে পাৰ্টিশ্বন, ৰাফটাৰ আৰু আঁকা পেটাৰ্ন আপুনি বিচৰা দূৰত্বত থাকে।
- ফল চিলিঙৰ উচ্চতা দেৱালৰ উচ্চতাৰ পৰা চিলিঙৰ ডাঠতাক বাদ দি নিৰ্ধাৰণ কৰকফল চিলিঙৰ আকৃতি আৰু ডাঠতা নিৰ্ধাৰণ কৰক, তাৰ পিছত ইয়াৰ উচ্চতা দেৱালৰ উচ্চতাৰ পৰা চিলিঙৰ ডাঠতাক বাদ দি নিৰ্ধাৰণ কৰক, যাতে চিলিং দেৱালৰ ওপৰৰ তলত শুদ্ধভাৱে থাকে।
- Turn on auto snapping to constrain walls to 90 degreesTurn on Orthogonal Snapping so the walls and lines you draw stay at 90 degrees, then join walls with Trim/Extend to Corner.
- Add a door to a wallPlace a door on a wall from the Architecture or Home tab and set it up in the Door panel.
- Sweep Tool ৰে কৰ্ণিছ, মৌল্ডিং আৰু ৱাল পেনেলিং যোগ কৰককাষ্টম কৰ্ণিছ, মৌল্ডিং আৰু সজোৱা ৱাল পেনেলিং যোগ কৰিবলৈ বেৰত Sweep Tool ব্যৱহাৰ কৰক, আৰু ৱাল মৌল্ডিং আৰু শ্বাটাৰ ডিজাইনৰ বাবে টাইলিং কাটিঙত sweep ম’ড ব্যৱহাৰ কৰক।
- Create and edit rooms from enclosed wallsEnclose four walls to get an automatic floor and room text, then rename the room and change its text properties.
- How ceilings and floors reference wallsLearn that a ceiling and floor in the design module can be created using a wall as a reference.
- Place doors after walls and edit size, height, thickness, hinge and modelAdd doors after your walls are ready, then adjust each door's size, orientation and model so it looks right in 3D.
- Set default door, window and wall properties via PreferencesSet default properties for repeated elements so newly added doors, windows, elevations and walls inherit the same values across all rooms.
- Set room dimensions from center or inner walls and pick room typeSwitch room dimensions to inner-wall measurements and choose a room type so Insert and Furnish only offers matching furniture and accessories.
- Set room inner dimensions and wall height before designingSet the left wall height and thickness and name the room so it is identifiable in the project before you start designing.
- এখন ৱিণ্ডো এটা ইয়াৰ ৱালত কেন্দ্ৰীভূত হৈছে নে নাই তাক জনাওকনিৰ্বাচিত ৱিণ্ডো এটা ইয়াৰ ৱালৰ লগত টানক আৰু ই কেন্দ্ৰত অৱস্থিত হৈছে নে নাই চাবলৈ গুলপীয়া চিহ্নবোৰ পঢ়ক।
- Trim an extra wall or room-divider segmentRemove an extra wall or room-divider segment using the trim shortcut T R or the trim option in the on-screen menu.
- দেৱাল, আচবাব আৰু টাইলিং যোগ কৰিবলৈ কীবৰ্ড চৰ্টকাট ব্যৱহাৰ কৰকআচবাব যোগ কৰা, দেৱাল অঁকা, টাইলিং যোগ কৰা বা দুৱাৰ স্থাপন কৰাৰ দৰে সাধাৰণ কামবোৰ এটা চুটি ক'ড টাইপ কৰি Enter টিপি চলাওক।
আৰু গাইড 2
সকলো দেখুৱাওক (2)
- AI floorplan generator ৰ সৈতে এটা মজিয়াৰ নক্সা সৃষ্টি কৰকএটা ইনপুটৰ পৰা এক মিনিটৰ ভিতৰত এটা মজিয়াৰ নক্সা প্ৰস্তুত কৰক, তাৰ পিছত অতি সৰু দৈৰ্ঘ্যৰ বেৰ আৰু বাৰাণ্ডা নিজে পৰীক্ষা কৰি শুধৰাই লওক।
- সৃষ্টি কৰা প্ৰ'ফাইলৰ দিশ শুদ্ধ কৰিবলৈ প্ৰ'ফাইলৰ অভিমুখ টগল কৰকটাইলিং আৰু কাটিং সঁজুলিত ৱাল আৰু টপ শ্বেপ বাছনি কৰক, তাৰ পিছত ভুল দিশত থকা সৃষ্টি কৰা প্ৰ'ফাইল ফ্লিপ কৰক।