panel और custom panel
गाइड: 252
- panel level पर visible और invisible edgeband मान सेट करेंpanel के front edge और शेष side को अपने-अपने edgeband मान दें, ताकि हर side इच्छानुसार finished हो।
- drawer height ठीक करने के लिए panel और drawer construction offsets को शून्य करेंकिसी drawer की ऊँचाई या fit गलत होने पर उसका height मान जाँचें और उसे प्रभावित करने वाले panel और bottom offsets को शून्य करके ठीक करें।
- fillet और panel thickness cut से panel edge को curved बनाएंfillet टूल से panel को curved edge दें, cut को panel thickness cut पर सेट करें और इसी treatment को mirror करके opposite side पर लगाएं।
- curved custom panel के साथ curved cabinetry को मॉडल करेंजानें कि curved custom panel से आप curved cabinetry केस कैसे मॉडल कर सकते हैं, और क्यों standard carcass panel को curved नहीं बनाया जा सकता।
- कैबिनेट construction formulas में panel thickness का संदर्भ लेंraw संख्याएँ टाइप करने के बजाय suggestions से thickness parameter चुनकर construction formula में panel की thickness का संदर्भ लें।
- कैबिनेट के दोनों side के लिए filler panel को क्लोन करें और संशोधित करेंएक filler panel को क्लोन करें और इसे इस तरह संशोधित करें कि कैबिनेट के प्रत्येक side को अपना अलग filler मिले।
- construction extension parameters के माध्यम से shutter panel width कम करेंकैबिनेट को कुल मिलाकर बदले बिना shutter panel को उसके left और right edge मानों को समायोजित करके संकीर्ण करें।
- panel hardware के माध्यम से panel में accessory drilling जोड़ेंlock जैसे accessory को panel पर panel hardware के रूप में रखें, उसे panel size के सापेक्ष स्थिति दें, और 2D CAM mode में drill positions जाँचें।
- Understand cabinet panel materials and linked finishesSee what each sub-tab under a cabinet's Materials holds and how linked finishes and profiles change edge bands and finishes automatically.
- Cut का उपयोग करके panel में आकृतियाँ काटें, Extrude के बजायpanel के face पर एक आकृति बनाएँ और आवश्यक गहराई पर cut-out या groove बनाने के लिए Extrude के बजाय Cut का उपयोग करें।
- panel thickness core material से कैसे निर्धारित होती हैजानें कि panel की thickness आपके द्वारा जोड़े गए core material से कैसे निर्धारित होती है।
- panel के inherited material को override करेंकिसी panel property को custom पर switch करें ताकि आप केवल उसी panel के लिए अलग material चुन सकें।
- डिज़ाइन में अलग-अलग panel पर grain ओरिएंटेशन घुमाएँडिज़ाइन मॉड्यूल में panel पर grain ओरिएंटेशन सेट करके और आवश्यकतानुसार प्रत्येक panel पर grain घुमाकर विशिष्ट panel पर grain direction नियंत्रित करें।
- कौन से panel cutlist और production output से चुपचाप बाहर रह जाते हैंजानें कि कौन से panel 3D design में रहते हुए भी cutlist, board layout और production output से बाहर हो जाते हैं, और उन्हें जानबूझकर कैसे बंद करें।
- construction edit panel design का उपयोग करके cutouts वाला custom panel बनाएँऊँचाई, चौड़ाई और core material thickness सेट करके एक vertical panel जोड़ें, construction edit panel design में cutout geometry बनाएँ, और cut को panel को असाइन करें।
- edit panel design और offset rectangle का उपयोग करके panel में cut बनाएँpanel की outline बनाए रखते हुए cut का आकार बनाकर और offset rectangle से उसका edge खिसकाकर panel में cut करें।
- edit shape से panel की गैर-आयताकार आकृति बनाएँpanel केवल 90-डिग्री आयतों तक सीमित नहीं हैं, और panel construction में आप अपनी इच्छानुसार कोई भी रूपरेखा बना सकते हैं।
- Round a panel corner via panel-level construction edit shapeGive a panel or shelf a rounded corner by selecting it, choosing edit shape in panel-level construction, picking the sides to curve and entering a radius.
- cut thickness को panel thickness के बराबर सेट करें और CAM में शामिल करेंpanel पर एक cut बनाएँ जिसकी thickness panel के बराबर हो और include in CAM विकल्प चालू हो, ताकि cut CAM आउटपुट तक पहुँचे।
- गोल आकार के लिए custom panel या architecture slab tool का उपयोग करेंऐसे गोल या curved तत्व को, जिसे मानक कैबिनेट production में नहीं ले जा सकता, custom panel के रूप में या architecture slab tool में मॉडल करके दर्शाएँ।
- कैबिनेट panel में लॉक जोड़ेंडिज़ाइन में panel में लॉक जोड़ें और इसे समायोजित करने के लिए panel size को 30 mm कम करें।
- drawer system में custom panel जोड़ें और उन्हें carcass material के रूप में map करेंdrawer system level पर custom panel जोड़ें और किसी भी panel level पर उनका material सेट करें ताकि उन्हें carcass material के रूप में map किया जा सके।
- संरेखित करने के लिए side fillers जोड़ें और panel बढ़ाएँpanel level construction में panel का front side जाँचकर और front depth extension को shutter panel thickness पर सेट करके panel को संरेखित करें।
- Edit Panel Design के माध्यम से shaped edge या beading profile लागू करेंpanel का Edit Panel Design विकल्प खोलें और shaped edge या beading profile लागू करने के लिए उसका profile बदलें।
- Edit Panel Design का उपयोग करके एक panel पर कई laminate लगाएंजिन area में अलग finish चाहिए, उन पर shapes जोड़कर एक ही panel को एक से अधिक laminate या material दें।
- आकार संपादित करके L-shaped panel बनाएँpanel खोलें, panel level पर जाएँ और L-shaped panel बनाना शुरू करने के लिए edit shape चुनें।
- cutouts जोड़ने और panel घुमाने के लिए panel design संपादित करेंpanel design संपादित करके back-panel grooving जैसे cutouts बनाएं और ज़रूरत पड़ने पर panel घुमाएं।
- कार्कस से shutter तक मापने के लिए मैन्युअल डाइमेंशनिंग हेतु shutter panel सक्षम करेंfloor plan में मैन्युअल डाइमेंशनिंग के लिए panel सक्षम करके और shutter panel चुनकर कार्कस से shutter तक मापें।
- construction settings और formulas का उपयोग करके panel को floor तक बढ़ाएँकिसी दिखाई देने वाले panel को उसकी construction settings के माध्यम से ज़मीन तक बढ़ाएँ और formulas से panel size नियंत्रित करें ताकि वे स्वतः समायोजित हों।
- exposed panel की फिनिश कैसे लागू होती हैजानें कि exposed panel को डिफ़ॉल्ट रूप से फिनिश कैसे मिलती है और किसी को अलग रूप कैसे दिया जाए।
- किसी एक unit की construction से panel हटाएँकेवल चयनित cabinet पर bottom जैसा panel बंद करें, component definition को बिना बदले।
- shutter panel का आकार Extension parameters से नहीं, Reduction से बदलेंExtension parameters के बजाय Reduction पैरामीटर का उपयोग करके shutter panel को बड़ा या छोटा करें।
- गैर-मानक आकारों के लिए custom panel जोड़ेंजब किसी shelf या partition को ऐसा आकार या स्थान चाहिए जो standard sizing parameters से नहीं बन सकता, तब custom panel जोड़ें।
- panel में groove जोड़ें और उसका CAM operation प्रकार सेट करेंनिर्दिष्ट गहराई वाला groove जोड़ने के लिए panel का आकार संपादित करें, फिर उसे CAM अनुभाग में शामिल करके उसका operation प्रकार सेट करें, जैसे routing।
- cabinet level पर एक horizontal custom panel जोड़ें और उसे rotate करेंcabinet-level custom panel का उपयोग करके cabinet में एक top panel जोड़ें, फिर एक horizontal custom panel जोड़ें और उसे कहीं भी रखें।
- जाँचें कि elevation preferences में panel का manual dimensioning सक्षम हैपुष्टि करें कि manual dimensioning के लिए panel सक्षम करने का विकल्प डिफ़ॉल्ट रूप से चालू है और देखें कि यह back और carcass panel को कैसे प्रभावित करता है।
- tandem box और none drawer panel निर्माण की तुलना करेंदेखें कि tandem box drawer में कौन से wooden panel होते हैं और none drawer में कौन से।
- Copy, multiply और fixed-distance विकल्प panel shapes की प्रतिलिपि बनाते हैंप्रत्येक shape को अलग-अलग बनाने के बजाय किसी रेखा या pattern के साथ panel shape दोहराने के लिए Copy, Multiply और Fixed Distance का उपयोग करें।
- extrude, offset move, fillet और cut के साथ custom panel डिज़ाइन बनाएँcustom panel डिज़ाइन बनाएँ और आकार दें, उसके corner गोल करें और एक through opening cut करें।
- curved vertical custom panel के लिए लंबाई और ऊँचाई की गणना मैन्युअल रूप से करनी होती हैएक vertical custom panel में curved विकल्प होता है।
- Edit Shape या Edit Panel Design के माध्यम से panel को अनुकूलित करेंpanel के outer आकार को बदलें, उदाहरण के लिए आयत से वृत्त या दीर्घवृत्त में, या edge वक्र जोड़ें।
- parametric मानों से panel और shutter dimension नियंत्रित करेंpanel और shutter dimension को parametric मान दें ताकि driving measurement बदलने पर वे स्वतः आकार बदल लें।
- skirting panel के लिए manual dimensioning सक्षम करेंpreferences में manual dimensioning चालू करें ताकि आप skirting panel को dimension कर सकें।
- panel dimension को fixed करें ताकि वह unit के साथ आकार बदलना बंद कर देpanel की length, depth या height को fixed मान पर सेट करें ताकि cabinet या wardrobe का आकार बदलने पर उस panel का panel size अपरिवर्तित रहे।
- कैबिनेट में custom panel रखेंcatalogue से या Add Custom Panel के साथ custom panel जोड़ें, डैशदार रूपरेखा का पालन करें और उसे स्थापित करने के लिए क्लिक करें।
- कस्टम कैबिनेट panel को curved आकार देंकस्टम horizontal panel को curved आकार दें और उसकी flat लंबाइयाँ, radius और arc angle सेट करें ताकि उसकी चौड़ाई expanded लंबाई के अनुसार हो।
- violations panel से या मैन्युअली रूप से drill collision हल करेंरिपोर्ट किए गए drill collision को violations सूची से हल करके दूर करें, फिर यदि वह अभी भी बना रहे तो offset को स्वयं समायोजित करें।
- wardrobe skirting construction में front panel और side panel को समझेंजानें कि wardrobe skirting construction में front panel और side panel कैसे बनाए जाते हैं।
- panel extension direction L, R, B और F को समझेंजानें कि चार extension direction L, R, B और F कैसे काम करते हैं और किसी side पर ऋणात्मक मान उस side से panel को कैसे घटाता है।
- construction के माध्यम से unit के अंदर एक पैरामीट्रिक custom panel जोड़ेंunit के अंदर एक horizontal top panel जोड़ें और उसका आकार तथा स्थिति पैरामीट्रिक फ़ॉर्मूलों से नियंत्रित करें।
- custom panel से horizontal या vertical panel और shelves जोड़ेंcabinet के अंदर horizontal या vertical panel रखने और उसे shelf में बदलने के लिए custom panel विकल्प का उपयोग करें।
- panel design के inner और outer area पर अलग-अलग रंग लगाएँpanel design बनाएँ और उसके base और applied रंगों को shutter external, carcass external, shutter या किसी custom finish से मैप करें, ताकि inner और outer area अलग-अलग रंग दिखाएँ।
- अपने properties से किसी filler panel का प्रकार और dimension बदलेंकिसी filler panel को उसके properties में dimension संपादित करके या उसे सही प्रकार के filler से बदलकर ठीक करें।
- व्यक्तिगत panel level पर लिंक किया गया panel फिनिश बदलेंव्यक्तिगत panel level पर किसी panel को custom के रूप में चिह्नित करें ताकि आप वहाँ उसकी लिंक की गई फिनिश या edge बैंड बदल सकें।
- material picker के माध्यम से panel का core material बदलेंmaterial picker खोलें, पेज पर core material चुनें, फिर panel level पर panel role सेट करें।
- panel section से एक single panel का material बदलेंएक panel चुनें और उसे cabinet-level material से अलग, अपना material दें।
- oversized-panel PDF डाउनलोड करके oversized panel जाँचेंऐसे panel खोजें जो board size से अधिक हैं और design में प्रत्येक को ठीक करें।
- single unit CAM mode में panel-to-panel connections जाँचेंकिसी cabinet के panels के बीच हर connection scenario देखें, हर एक कौन-से connector cards उपयोग करता है, और वास्तविक drills देखें।
- shelf panel सेटिंग्स में fixed या adjustable shelves चुनेंतय करें कि प्रत्येक shelf स्थायी रूप से अपनी जगह पर रहे या उसे हटाकर दोबारा लगाया जा सके, और साफ़ drawer लुक के लिए shelves को fixed सेट करें।
- नियंत्रित करें कि मैनुअल डाइमेंशनिंग किन panel पर स्नैप करेएलिवेशन में मैनुअल डाइमेंशनिंग किन panel type पर स्नैप करे, यह 'Enable panels for manual dimensioning' सेटिंग में उन्हें चुनकर तय करें।
- panel में एक center cutout बनाएंcutout shape बनाएं, click-and-move से उसे स्थिति दें, फिर panel को panel thickness पर cut through करने के लिए सेट करें।
- open wall unit panel बनाएं और shutter mechanism को none पर सेट करेंजब unit shutter न हो, तो shutter mechanism को none पर सेट करें।
- closed boundary वाली आकृतियों को panel में cut करेंएक closed boundary आकृति बनाएं, उसे cut के रूप में चिह्नित करें और cut depth सेट करें ताकि सॉफ़्टवेयर को पता चले कि panel को कहाँ cut करना है।
- Change Length, Shift Edge और Offset से panel का आकार संपादित करेंEdit Shape में panel की रूपरेखा बदलें और उसके अंदर frame जोड़ने के लिए Edit Panel Design में Offset का उपयोग करें।
- construction section में panel designs संपादित करेंpanel size घटाने और निर्दिष्ट dimension के साथ cut के रूप में परिभाषित कस्टम आकार या कटआउट जोड़ने के लिए construction section में panel designs संपादित करें।
- panel को मैन्युअल dimensioning के लिए Annotate Align उपयोग करने की अनुमति देंवह प्राथमिकता चालू करें जिससे panel Annotate Align उपयोग कर सकें, ताकि आप design पर dimension हाथ से रख सकें।
- L-shaped custom panel thickness कैसे निकाली जाती हैजानें कि L-shaped custom panel के कौन-से dimension आप सेट कर सकते हैं और उसकी thickness fixed क्यों है।
- tandem drawer के panel size कैसे निकाले जाते हैंजानें कि tandem drawer के bottom और back panel की panel depth और ऊँचाई tandem item के dimension से कैसे निकाली जाती है।
- कैबिनेट के अंतर्गत custom panel कैसे सूचीबद्ध होते हैंजानें कि custom panel किस कैबिनेट के अंतर्गत सूचीबद्ध होता है, यह इस पर निर्भर करता है कि आप उसे कहाँ जोड़ते हैं।
- panel dimension, dimension, extension और cabinet adjustments से कैसे निर्धारित होते हैंजानें कि किसी panel की कुल thickness उसके core material और finishes से कैसे निकाली जाती है, और pre-laminated तथा post-laminated core material के लिए यह गणना कैसे अलग होती है।
- दोनों side panel पर minifix और dowel का orientation एक समान रखेंcarcass के दोनों top edge को एक ही construction पर सेट करें, ताकि left और right side panel पर minifix और dowel connector एक ही direction में चलें।
- plain panel के पीछे box-type filler का उपयोग करके backlit panel बनाएंplain front panel के पीछे box-type filler जोड़कर और उसके अंदर strip light रखकर backlit panel बनाएं।
- panel design shape को विपरीत shutter पर mirror करेंचयनित shape को MI से mirror करें, operation को copy से move में बदलें, और centre top से centre bottom तक चुनें ताकि यह विपरीत shutter पर पहुँच जाए।
- translate panel का उपयोग करके किसी ऑब्जेक्ट को सटीक दूरी तक ले जाएँtranslate panel के axis position फ़ील्ड में मान दर्ज करके चयनित ऑब्जेक्ट को सटीक दूरी तक ले जाएँ।
- panel boundary को निर्धारित दूरी से ऑफ़सेट करेंबिना मैन्युअल रूप से मापे सभी side पर एक समान मार्जिन पाने के लिए panel boundary को outer edge से ऑफ़सेट करें।
- partition height, depth और shelf reveal का उपयोग करके partition panel को स्थिति देंcustom panel जोड़कर, उसे घुमाकर और उसका left-right dimension तथा X और Y स्थिति सेट करके एक क्षैतिज partition panel रखें।
- दर्ज किए गए और cutlist panel dimension पढ़ेंदेखें कि किसी panel का संपादन योग्य dimension cutlist और board layout तक पहुँचने वाले मान से क्यों भिन्न होता है।
- panel-स्तरीय कस्टमाइज़ेशन से shutter panel का विभाजन हटाएँshutter panel पर विभाजन हटाएँ ताकि shutter बिना split लाइन के एक ही panel के रूप में दिखे।
- fixed दूरी पर multiply से panel दोहराएँ या multiply fixed copy करेंकिसी panel को निर्धारित अंतराल पर दोहराएँ, या fixed संख्या में panel पूरी wall पर समान रूप से फैलाएँ।
- unit पर exposed side panel सेट करेंunit को panel level पर खोलें और panel को exposed panel में बदलें, क्योंकि इसे unit-level default के रूप में सेट नहीं किया जा सकता।
- front panel और bottom panel extension सेट करेंdrawer system के लिए Front Panel Extension और प्रति-side Bottom Panel Extension मान कॉन्फ़िगर करें।
- sliding door panel sizing और construction parameters सेट करेंsliding door panel का आकार निर्धारित करें और नियंत्रित करें कि उनके ट्रैक और panel carcass के सापेक्ष कैसे स्थित हों।
- gola और G-profile कैबिनेट के लिए top panel का आकार निर्धारित करेंजानें कि gola profile top panel को पीछे की ओर कैसे ऑफ़सेट करता है, जबकि G-profile इसे carcass के आकार में रखता है।
- Split top and bottom panels प्रति vertical partitionकैबिनेट के top and bottom panel को प्रत्येक vertical section के लिए एक टुकड़े में split करें, ताकि प्रत्येक टुकड़ा अपने section की चौड़ाई के अनुसार हो और edge टुकड़े स्वतः side पर फैल जाएँ।
- समझें कि panel extension कैसे मापा जाता हैजानें कि panel extension की गणना carcass depth और shutter thickness को जोड़कर की जाती है, तथा डिफ़ॉल्ट सिस्टम carcass और shutter के बीच 2 mm का gap बनाए रखता है।
- समझें कि panel material कहाँ से आते हैंदेखें कि panel की भूमिका के आधार पर प्रत्येक panel का core, finishes और edgeband unit-स्तरीय चैनलों से कैसे विरासत में मिलते हैं।
- hardware rule में shutter variants को अलग पहचानने के लिए panel type शर्त का उपयोग करेंकिसी विशेष shutter variant को उसका अपना panel type दें, ताकि hardware rule उसे shutter design tag के बिना भी अलग पहचान सके।
- कोणीय कैबिनेट आकारों के लिए custom panel का उपयोग करेंमानक कैबिनेट panel को घुमाने के बजाय एक अलग custom panel का उपयोग करके कोणीय या गैर-मानक कैबिनेट आकार बनाएं।
- कैबिनेट पर custom panel जोड़ें और उसका आकार निर्धारित करेंकैबिनेट के Construction टैब से custom panel जोड़ें, फिर उसका shape, dimension और position सेट करें, और जब panel किसी unit के अंदर हो तो unit parameters के expressions का उपयोग करें।
- wardrobe के नीचे bottom support panel जोड़ेंbottom support panel की संख्या और ऊँचाई सेट करें ताकि वे plinth zone में cabinet bottom के नीचे समान रूप से खड़े हों।
- Add connector परिदृश्यों को बल्क रीस्ट्रक्चर के माध्यम से कैबिनेट panel से जोड़ेंBulk Restructure के माध्यम से styles से आयात करके hardware connector परिदृश्यों को कैबिनेट panel से जोड़ें।
- panel में groove, cut और extrusion जोड़ेंdoor या panel पर आकृति बनाने और उसे cut या extrude करके सुंदर पैटर्न या कस्टम कटआउट बनाने के लिए Edit Panel Design टूल का उपयोग करें।
- shelf या individual panel level पर panel front thickness समायोजित करेंcarcass front से shelf और panel को सटीक रूप से स्थित करने के लिए shelf और panel reveals को मिलीमीटर में सेट करें।
- बाहरी drawer का आकार बदलने के लिए panel-स्तर की कमी समायोजित करेंबाहरी drawer को बड़ा बनाने के लिए panel-स्तर की कमी वाले पैरामीटर को ऋणात्मक मान के साथ बदलें।
- split skirting segments को panel type असाइन करेंsplit skirting segments को वे panel type दें जिनसे hardware और connector नियम उन्हें unsplit skirting से अलग पहचान सकें।
- single और top chimney panel के बीच चुनेंवह chimney panel variant चुनें जो आपको केवल front देता है या front और top दोनों देता है।
- Solve Collisions से panel collision साफ़ करेंकई panel collision स्वचालित रूप से साफ़ करने के लिए Solve Collisions विकल्प का उपयोग करें।
- panel और box label, field और logo की जगह कॉन्फ़िगर करेंसेट करें कि कौन-से प्रति-panel field panel label पर प्रिंट हों और box label पर organization logo कहाँ हो।
- पूर्ण top के लिए half-top panel को false होने की पुष्टि करेंhalf-top panel सेटिंग जाँचें ताकि पूर्ण top सही ढंग से बने।
- तय करें कि panel का material कब fixed करना हैमौजूदा panel को संपादित करने और नया panel जोड़ने के बीच चुनें, और custom material केवल उन्हीं panels के लिए रखें जिन्हें fixed रहना है।
- panel extension और offset को parameters से नियंत्रित करेंextension मानों, offsets और cutouts को design parameters से जोड़ें ताकि मॉडल बदलने पर वे अपडेट हो जाएँ।
- शेल्फ़ और partition को बल्क-चुनने के लिए panel को type से फ़िल्टर करेंpanel सूची को unit SK नाम और panel type से फ़िल्टर करें, ताकि आप एक साथ कई शेल्फ़ या partition चुन सकें और एक ही क्रिया में उनकी finish बदल सकें।
- ऐसे panel खोजें जो carcass material का पालन नहीं करतेcore section के अंतर्गत custom core property देखकर ऐसे panel पहचानें जिनका custom core material carcass का पालन नहीं करता।
- panel का internal finish जो बदलता नहीं, उसे ठीक करेंजब किसी panel का internal finish किसी भी output में नहीं बदलता, तो हो सकता है कोई automation rule उसे override कर रहा हो।
- panel height के साथ आकार न बदलने वाले laminate को ठीक करेंजानें कि panel height बदलने पर मैन्युअल रूप से पेस्ट किया गया laminate या colour rectangle fixed स्थिति और आकार में क्यों रहता है।
- अनपेक्षित material प्राप्त करने वाले skirting panel ठीक करेंजब हर नए design में skirting panel गलत material ले लेता है, तो जाँचें कि कोई admin skirting preference component की कॉन्फ़िगर की गई inheritance को override तो नहीं कर रही।
- स्टैक किए गए panel को निचले panel thickness के बराबर front shift देंऊपरी panel को उसके नीचे वाले panel की thickness के बराबर front shift दें ताकि दोनों सतहें overlap न हों।
- preferences में back और front panel extension कैसे सेट किए जाते हैंजानें कि preferences में back, front और drawer bottom extension अलग-अलग कैसे कॉन्फ़िगर किए जाते हैं।
- exposed panel में shutter core और finish कैसे लागू होते हैंजानें कि किसी panel को exposed panel में बदलने पर उसके core material, finish और board layout के साथ क्या होता है।
- panel पर extrusion और cut में क्या अंतर हैजानें कि extrusion कैसे panel की सतह से बाहर की ओर उभरता है, जबकि cut उसमें खुदाई करता है, चाहे वह पूरी तरह कटा हुआ cutout हो या तय गहराई तक।
- panel drill details में connector, hardware SKU और rule कैसे दिखते हैंकिसी design में panel की drill चुनने पर connector, hardware SKU, लागू rule और drill dimensions दिखते हैं, और इन मानों को admin portal में बदला जा सकता है।
- panel thickness सूत्र cabinet-level core material को कैसे पढ़ते हैंजानें कि carcass panel thickness या shutter panel thickness जैसा panel thickness सूत्र अपना मान कहाँ से लेता है।
- किसी चयनित panel को उसके Panel ID से पहचानेंजब आप कोई panel चुनते हैं, तो left panel कई पहचानकर्ता दिखाता है, और Panel ID सबसे अंत में दिखाया जाता है।
- किसी panel को दूसरे finish के अनुसार बनाएंकिसी panel के finish slot को दूसरे finish से लिंक करें, ताकि panel उसे इनहेरिट कर ले और वह finish बदलने पर अपने आप अपडेट हो जाए।
- Position panel के अक्षों के साथ gimbal तीरों के रंग मिलाएँजानें कि प्रत्येक gimbal तीर का रंग आपको बताता है कि Position panel में कौन-सा अक्ष मान संपादित करना है।
- बचे हुए site gap से चौड़े filler panel order करेंdesign में वास्तविक gap से बड़ी panel width दर्ज करें, क्योंकि panel आपके द्वारा दर्ज किए गए आकार में बनाया जाता है।
- गैर-मानक rails और supports के लिए custom panel रखेंमानक संरचना जहाँ rails या supports प्रदान नहीं करती, वहाँ cabinet के अंदर custom panel जोड़ें।
- 2D panel मोड में XYZ निर्देशांकों के साथ ड्रिल की स्थिति निर्धारित करें2D panel मोड में ड्रिल जोड़ें और डिफ़ॉल्ट स्थिति में ऑफ़सेट लागू करके उनकी जगह को ठीक करें।
- panel 2D CAM में सॉफ़्टवेयर-जनित operation हटाएँजानें कि panel 2D CAM में कुछ operation सीधे क्यों नहीं हटाए जा सकते और shape को revert करके उन्हें कैसे हटाया जाए।
- shortcut panel की search में कोई भी command या shortcut खोजेंमेन्यू में ढूँढ़ने के बजाय shortcut panel की search में टाइप करके कोई भी command या shortcut खोजें।
- design portal में panel का प्रकार देखेंSelect a panel खोलें और panel name तथा panel type देखने के लिए उसका info विकल्प खोलें।
- properties panel में किसी element के properties देखेंकिसी design में कोई भी element चुनें और properties panel में उसके properties देखें, जिनमें wall, door और window की बारीकियाँ भी शामिल हैं।
- Select a panel profile, panel के लिएprofile कॉन्फ़िगर हो जाने के बाद, जिस panel को आप डिज़ाइन कर रहे हैं उसके लिए उपलब्ध विकल्पों में से चुनें।
- filler panel level पर X offset को zero पर सेट करेंसही placement के लिए filler panel level पर काम करते समय X offset को zero पर सेट करें।
- नियमों के मिलान के लिए custom panel का panel type सेट करेंcustom panel को सही panel type दें ताकि panel-type नियम और उनके connector उस पर लागू हों।
- shelf panel को adjustable shelf प्रकार में सेट करें और उसमें glass core रखेंshelf panel को adjustable shelf प्रकार में सेट करें और उसे glass core material दें, जैसे किसी दी गई thickness का tinted glass।
- प्रत्येक panel के लिए panel दृश्यता और फ़िनिश सेट करेंफ़िनिश बदलने से पहले सही panel चुनें, क्योंकि दृश्यता सेटिंग्स प्रत्येक panel के लिए लागू होती हैं।
- bottom panel को उठाने के लिए bottom panel offset सेट करेंSet the bottom panel offset to control the clear gap below the bottom panel and raise it by the side panel height when needed.
- व्यापक carcass panel के बजाय विशिष्ट panel लक्षित करेंकिसी नियम की panel-type शर्त को सीमित करें ताकि connector केवल उन्हीं panel पर लगें जिन्हें आप चाहते हैं।
- corner unit panel हेडिंग और कोटेशन श्रेणियों को समझेंजानें कि corner unit की panel हेडिंग और विवरण अन्य base unit, wall unit और tall unit product से कैसे भिन्न हैं और यह Pricing Quotation में कैसे दिखता है।
- समझें कि furniture light का panel अपने light sources को कैसे सूचीबद्ध करता हैजानें कि furniture light का panel प्रत्येक light source को स्थिति के अनुसार कैसे सूचीबद्ध करता है और उसके properties तथा multi-selection व्यवहार क्या हैं।
- समझें कि हार्डवेयर ड्रिलिंग में कौन सा panel panel two हैजानें कि जब कोई drill किसी panel के edge band पर पड़ता है, तो कौन सा panel panel two के रूप में वर्गीकृत होता है।
- बल्क फिनिश बदलाव के बाद Custom Finish वाले panel अपडेट करेंप्रोजेक्ट की फिनिश बल्क में बदलें, फिर जिन panel का finish source Custom Finish पर सेट है, उन्हें panel पर एक-एक करके अपडेट करें।
- panel के left, right, top and bottom को समायोजित करने के लिए reduction options का उपयोग करेंconstruction panel settings में panel के left, right, top and bottom पर reductions सेट करें, जहाँ आप जो संख्या दर्ज करते हैं वह उस panel dimension को कम करती है।
- कारकास, side panel और edge band फिनिश को shutter से मिलाएँकारकास और side panel की फिनिश अलग-अलग सेट करें और edge band को shutter की दृश्यमान edge band सेटिंग का पालन करने दें।
- चयनित shutter panel पर shutter design लागू करेंModify Shutter Design लाइब्रेरी खोलें, एक design चुनें और उसे चयनित shutter panel पर उनके finished size पर लागू करें।
- किसी panel को लक्ष्य गहराई तक या पीछे तक बढ़ाएँलक्ष्य कुल गहराई तक पहुँचने के लिए सही extension मात्रा दर्ज करें या panel को कैबिनेट के पीछे तक चलाएँ।
- sliding shutter system डालें और panel पर external finish लगाएँsliding shutter system डालकर, panel design विकल्पों को अनुकूलित करके और panel पर external finish लगाकर wardrobe पूरा करें।
- फिनिश लगाने से पहले panel पर edge बैंड सेट करेंcatalogue में edge बैंड प्रविष्टियाँ बनाएँ, प्रत्येक panel या shutter पर प्रति side उन्हें असाइन करें, और panel level सेटिंग्स से किसी एक edge पर फिनिश बदलें।
- panel level पर panel को edit करके back panel thickness बदलेंpanel level पर उस एक panel को edit करके back panel को मोटी carcass thickness दें, जैसे island kitchen के लिए 18 mm।
- custom panel और panel design संपादनों के साथ एक curved cabinet बनाएँcabinet level पर एक custom panel जोड़कर, उसे carcass parameters से sizing करके, और उसके offsets समायोजित करके ताकि वह सही ढंग से बैठे, एक curved cabinet बनाएँ।
- अन्य shutters या panels को प्रभावित किए बिना एक single shutter या panel को override करेंएक shutter को अपना design और finish दें या एक single panel के materials बदलें, जबकि cabinet का बाकी हिस्सा वैसा ही रहे।
- कस्टम support panel जोड़ें और back panel offset तथा grooving सेट करेंअपने core material, finish और label वाला support panel जोड़ें, और extension parameters में back panel offset तथा grooving depth कॉन्फ़िगर करें।
- panel level पर shutter का core material glass में बदलेंshutter के core को plain glass जैसे कस्टम material में बदलें और चुने गए core के माध्यम से glass की thickness सेट करें।
- shutter system configuration और panel edits के बीच चुनेंतय करें कि glass और frame variations को कब shutter system configuration से प्रबंधित करना है और कब panel material को सीधे संपादित करना है।
- cabinet panel पर set distance पर strip light जोड़ेंcabinet panel पर strip light जोड़ें और panel edge से उसकी दूरी सेट करें।
- डिज़ाइन में cabinet back, top, bottom और side panel कॉन्फ़िगर करेंप्रत्येक cabinet panel को अलग-अलग कॉन्फ़िगर करें ताकि उसका आकार, material, edge band, lighting और hardware आपकी आवश्यक construction से मेल खाए।
- कैबिनेट के हर panel पर एक edge band लगाएँedge band को cabinet level पर जोड़ें ताकि वह उस कैबिनेट के हर panel पर लागू हो।
- समान edge को panels पर लागू करने के लिए construction style बनाएँconstruction style बनाएँ ताकि अलग-अलग panels पर समान edge लागू हो, फिर प्रत्येक element के लिए उसे ठीक करें।
- panel-level edit panel design के माध्यम से shutter में cutout बनाएँpanel-level edit panel design में आकार बनाकर और उसे panel thickness में cut करने के लिए सेट करके shutter से एक आकार cut करें।
- skirting दिखाने के बजाय panel को floor तक नीचे बढ़ाएँpanel की construction settings में extension parameters का उपयोग करके panel को skirting दिखाने के बजाय floor तक जारी रखें।
- back and drawer bottom panel के लिए स्वचालित grooving को समझेंजानें कि सॉफ़्टवेयर कब स्वचालित रूप से grooving जोड़ता है और सभी unit में एक साथ back panel grooving को कैसे बदलें।
- कैबिनेट panel में strip light या spotlight जोड़ें और उसका light source सेट करेंकैबिनेट panel में strip light या spotlight जोड़ें, spotlight को light source दें और उसकी स्थिति सेट करें, और आवश्यकता न होने पर दोनों में से कोई भी light हटा दें।
- partition या panel level पर shelf reveal समायोजित करेंclash दूर करने के लिए partition level पर shelf reveal बदलें या panel level पर किसी एक shelf का front edge खिसकाएँ, ताकि आंतरिक shelves clash से बच जाएँ।
- shutter को panel और partition के साथ संरेखित करेंप्रति-edge कमी को समायोजित करें ताकि shutter flush बैठे, पूरी ऊँचाई पर रहे या partition खुला छोड़े।
- cabinet level पर shutter का रंग और panel level पर panel की फिनिश बदलेंपूरे cabinet के लिए shutter का रंग और अलग-अलग panel के लिए external finish सेट करें।
- construction tab का उपयोग करके panel को बढ़ाएँconstruction tab में extension मान दर्ज करके panel को उसके left, right, front या back side पर बढ़ाएँ।
- extension पैरामीटर से panel edge को बढ़ाएँ या घटाएँpanel edge को लंबा या छोटा करने के लिए चारों दिशाओं वाले extension फ़ील्ड का उपयोग करें, जिसमें ऋणात्मक मान भी शामिल हैं।
- carcass panel और shutter panel के लिए hinge की मात्रा कैसे जनरेट होती हैजानें कि hinge की गिनती carcass panel और shutter panel के बीच इंटरैक्शन से क्यों होती है, और जब carcass panel बंद होता है तो क्या होता है।
- wardrobe के side panel कैसे floor तक पहुँचते हैंजानें कि wardrobe के side panel पूरी लंबाई में floor तक कैसे जाते हैं और front skirting के लिए cutout क्यों बनाया जाता है।
- side panel या side skirting के बीच inset back skirtingback skirting इस तरह जोड़ें कि वह side panel या side skirting के बीच inset रहे, जिससे side panel skirting के सिरों को बंद कर दें।
- panel level पर strip light जोड़ेंbottom panel में एक strip light जोड़ें और उसका reference सेट करें, फिर left जैसे अन्य panel के लिए दोहराएँ।
- drawer height, channel और bottom panel thickness को कस्टमाइज़ करेंdrawer height, channel सेटिंग्स और bottom panel thickness को समायोजित करें ताकि drawer निर्माण आवश्यक dimension से मेल खाए।
- drawer height, front panel reduction और carcass 1mm reduction सेट करेंआवश्यक heights के साथ drawer settings structure और drawer-level construction कॉन्फ़िगर करें, फिर drawer level पर front panel reduction सेट करें।
- center cabinet side panel निर्माण को समझेंजानें कि center cabinet side panel डिफ़ॉल्ट रूप से कैसे बनते हैं और left, right, top and bottom panel एक साथ कैसे जुड़ते हैं।
- quick access panel में kitchen cabinet height को समझेंजानें कि kitchen cabinet के quick access panel में दिखाई गई height क्या मापती है और उसे संपादित करने से क्या बदलता है।
- panel पर finish कॉपी करने के लिए custom finish और match property का उपयोग करेंजिस panel का external finish source-driven है, उस पर विशिष्ट finish लगाने के लिए panel चुनें, external finish source खोलें और custom finish चुनें।
- wall cabinet के bottom panel में strip light और spotlight जोड़ेंwall cabinet के bottom panel में strip light और spotlight जोड़कर उसे प्रकाशित करें।
- wall unit panel में strip light जोड़ें और उसका रंग सेट करेंकिसी wall unit को light करने के लिए उसके panel में strip light जोड़ें, front या back चुनें, और design की Lights preferences में रंग सेट करें।
- wall section के properties panel से wall skirting लागू करेंwall section के properties panel में Wall Skirting चालू करें और wall पर लागू करने के लिए skirting finish चुनें।
- countertop thickness बदलने से top panel अपने आप नहीं बदलताजानें कि countertop thickness बदलने पर kitchen base unit का top panel rail panel क्यों रहता है।
- panel design को edit करके और cutting करके curved shutter बनाएँshutter का आकार Edit Panel Design में draw करें और curved shutter बनाने के लिए उसे panel thickness तक cut करें।
- panels को स्वचालित रूप से समायोजित करने के लिए skirting height निर्धारित करेंskirting height का मान बदलें ताकि समग्र height फिर से लागू हो और panel बिना मैन्युअल संपादन के समायोजित हो जाए।
- drawer bottom panel को drawer side में groove कैसे किया जाता हैजानें कि Infurnia drawer bottom panel को drawer side में कैसे groove करता है, जिसमें wooden drawer निर्माण में उपयोग किया जाने वाला चारों ओर से grooving भी शामिल है।
- कैबिनेट end panel का आकार design panel level पर बदलें, admin portal में नहींdesign चरण में panel level पर कैबिनेट end panel की गहराई बदलें, ताकि बदलाव केवल उसी कैबिनेट पर लागू हो जिस पर आप काम कर रहे हैं।
- kitchen base corner unit के top panel को समझेंजानें कि kitchen base corner unit में पूरा top panel उपयोग होता है।
- custom panel फर्नीचर विकल्प का उपयोग करके एक कस्टम ply panel जोड़ेंfloor पर एक कस्टम ply panel रखें, उसका आकार निर्धारित करें और 3D view में उसे जाँचें।
- Furnish विकल्प से कस्टम horizontal या vertical panel जोड़ेंloft और wall unit के बीच की जगह जैसे gap को कस्टम add-on panel से भरें, जिनका आकार और स्थान axis controls से तय करें।
- panel section construction के माध्यम से shelf में profile जोड़ेंआवश्यक side पर panel section की construction/top settings से profile जोड़कर उसे shelf पर रखें।
- panel edit panel design के माध्यम से कस्टम groove बनाएँpanel पर एक groove आकृति बनाएँ, उसे गहराई और material के साथ cutout के रूप में सेट करें, फिर उसे fixed दूरी पर दोहराएँ।
- पैरामीट्रिक फ़ॉर्मूलों के साथ panel design में drawer cutouts बनाएँpanel design में carcass panel पर एक आयत बनाएँ और उसके edge को पैरामीटर से नियंत्रित करें, ताकि drawer opening स्वतः अपडेट हों।
- vertical panel को अंदर की ओर करके side-by-side drawer बनाएँfixed shelf और vertical से section को आधों में split करें, प्रत्येक आधे को एक drawer set दें, फिर panel को अंदर की ओर खिसकाकर vertical छिपाएँ।
- R handle का उपयोग करके panel side को बढ़ाएँR handle का उपयोग करके panel को निर्दिष्ट मात्रा, जैसे 100 mm, तक बढ़ाएँ।
- bottom panel को बढ़ाकर उस gap को ढकें जहाँ skirting टूटती हैpanel चुनें और इसे बढ़ाकर उस gap को ढकें जहाँ अन्यथा अलग skirting टूट जाती।
- curved panel और उनकी cutlist लंबाई को संभालेंएक curved panel को एक ही टुकड़े के रूप में मॉडल करें और cutlist तथा कोटेशन में उसकी समतल की गई खाली लंबाई देखें।
- panel पर shutter रंग और प्रति-area रंग कैसे मिलते हैंजानें कि shutter रंग किस प्रकार multi-area panel का base रंग तय करता है, जबकि जिन area को अपना रंग दिया गया है वे उसे बनाए रखते हैं।
- carcass panel thickness का उपयोग करके bottom panel को अंदर की ओर offset करेंbottom panel को एक panel thickness ऊपर उठाएँ ताकि वह side panel के नीचे के बजाय carcass के अंदर बैठे।
- bottom elevation और bottom panel offset के साथ drawer box को स्थिति देंbottom elevation से drawer box को shutter के bottom से ऊपर उठाएँ और bottom panel को उसके offset से ठीक करें, यह ध्यान रखें कि offset drawer box की ऊँचाई घटा देता है।
- skirting panel पर negative extension का उपयोग करके skirting का आकार घटाएँpanel editor में negative extension लगाकर skirting run को छोटा करें और skirting के चारों ओर side panel फिट करें।
- कैबिनेट panel के अपने स्तर पर फ़िनिश और शेल्फ़ विकल्प सेट करेंकिसी कैबिनेट panel का अपना स्तर खोलकर चुनें कि उसकी बाहरी और internal finish कहाँ से आएँ, केवल उसी panel के लिए कस्टम फ़िनिश चुनें, और शेल्फ़ का प्रकार और दृश्यता सेट करें।
- collision से बचने के लिए प्रत्येक panel पर strip light की स्थिति सेट करेंप्रत्येक panel पर strip light की स्थिति front या back edge से दूरी के रूप में परिभाषित करें ताकि light collision से बचें।
- समझें कि scenarios carcass panel और meeting panel को कैसे सूचीबद्ध करते हैंजानें कि एक scenario पहले carcass panel का नाम कैसे लेता है और दूसरे में उस panel का जिससे वह मिलता है, और meeting side को face के रूप में दिया जाता है।
- partition को समझें और cabinet के अंदर shelves, panel या drawer जोड़ेंजानें कि Infurnia में partition क्या है और partition level पर shelves, vertical panel या drawer जोड़ें।
- मैनुअल panel के बजाय box frame के लिए बहुउद्देशीय मॉडल फर्नीचर का उपयोग करेंऐसा unit रखें जिसमें उसका frame box पहले से शामिल हो और depth मान संपादित करके box की गहराई समायोजित करें।
- cabinet, partition, shutter और panel नियंत्रणों तक पहुँचने के लिए selection tree का उपयोग करेंकिसी cabinet part का चयन करें ताकि उसके ऊपर के स्तर दिखें और सीधे आपके आवश्यक नियंत्रणों पर जाएँ।
- Furnish > Panels के माध्यम से कस्टम vertical panel जोड़ें और laminate finish लगाएंइसका material और finish चुनकर, फिर इसके dimension सेट करके कस्टम vertical panel बनाएं।
- drawer panel से drawer fascia डिज़ाइन बदलेंdrawer panel से एक अलग drawer fascia डिज़ाइन चुनें।
- panel level पर skirting के लिए edge binding बदलेंकिसी skirting area को panel level पर बदलकर shutter से अलग अपनी edge binding दें।
- एक internal panel और shutter के बीच hinge custom scenario बनाएँconnector source को manual पर सेट करें, फिर scenario connector बनाएँ और संबंधित connector card जोड़ें, जैसे blind corner connector।
- Edit Panel Design में cut shapes के लिए edge banding और materialजानें कि Edit Panel Design में cut shapes पर edge banding कैसे लगाई जा सकती है और इच्छित finish के लिए material कैसे चुना जाता है।
- Edit connector कार्ड स्पेसिंग प्रति कैबिनेट single unit panel CAM मोड मेंकेवल एक कैबिनेट के लिए connector कार्ड स्पेसिंग बदलें, बिना किसी अन्य कैबिनेट को प्रभावित किए।
- डिज़ाइन इंटरफ़ेस को समझें: levels bar, plan/3D toggle और properties panelडिज़ाइन इंटरफ़ेस में levels bar, floor plan और 3D toggle, समूहित toolbar, properties panel और presentation sheets खोजें।
- panel-level visibility से carcass panel छिपाएँ या हटाएँcabinet के Construction > Carcass > Carcass Panels Visibility से एक single carcass panel बंद करें।
- properties panel से countertop और handles बदलेंउनका countertop material और thickness बदलने या properties panel से उनके handles बदलने के लिए Select units।
- देखें कि unit-स्तर के बदलाव panel तक कैसे पहुँचते हैंजानें कि unit-स्तर का material बदलाव कब किसी panel तक पहुँचता है और कैसे automation नियम और linked SKU उसे override कर सकते हैं।
- drawer filler की चौड़ाई सेट करें और filler panel material thickness मिलाएँdrawer filler panel को मोटा करने के लिए उसे अपना custom core material दें, ताकि वह आसपास के 25 mm board से मेल खाए।
- top panel के लिए carcass railing विकल्प सेट करेंcarcass railing विकल्प सेट करें ताकि top panel एक rail panel या पूरा panel हो, और आवश्यक डिज़ाइन से मेल खाने के लिए प्रत्येक side की construction समायोजित करें।
- Edit panel design का उपयोग करके side panel को angled top से मिलाने के लिए trim करेंEdit panel design या Edit shape का उपयोग करके side panel को इस तरह समायोजित करें कि वह custom angled top panel के angle से मेल खाए।
- cabinet, wardrobe और custom panel श्रेणियों को समझेंजानें कि Infurnia unit को तीन अलग श्रेणियों में कैसे व्यवस्थित करता है: cabinet, wardrobe और custom panel।
- end panel और side panel को अलग-अलग panel type के रूप में समझेंजानें कि कैबिनेट के side panel और end panel अलग-अलग panel type हैं, जिनकी अपनी extension सेटिंग्स होती हैं।
- दृश्यमान panel side पर Design Check machining चेतावनी को समझेंजानें कि Design Check उन panels को समस्या के रूप में क्यों रिपोर्ट करता है जिनके दृश्यमान side पर machining है।
- कारकस width और thickness से sized एक custom horizontal panel जोड़ेंकैबिनेट के अंदर एक horizontal custom panel जोड़ें और इसे carcass width, depth और panel thickness से size करें ताकि यह सही ढंग से align हो।
- ढलान वाले top के लिए कस्टम inclined panel जोड़ेंढलान वाले top के लिए कस्टम inclined panel जोड़ने के लिए आवश्यक incline की गणना करें और panel dimension उसी के अनुसार बढ़ाएँ।
- Furnish panel dropdowns से kitchen unit जोड़ेंFurnish panel dropdowns से अपने kitchen plan में base, sink, drawer, tall/appliance और filler unit जोड़ें।
- Add strip lights to a panel and set their side, orientation and positionAdd a strip light from the selected panel's panel options, then move it to the other face, choose Horizontal or Vertical, and shift it along the panel.
- panel पर strip light लगाएँ3D model में एक पीला strip light रखें।
- material panel में उपश्रेणी खोजकर material असाइन करेंmaterial या properties panel खोलें और चयनित geometry पर लागू करने के लिए कोई material चुनें।
- डिज़ाइन में panel level पर utility hardware मैन्युअल रूप से अटैच करेंpanel को चुनकर और panel hardware सूची से आइटम जोड़कर panel पर utility hardware अटैच करें।
- शेल्फ़ और वर्टिकल panel से विभाजित करके cabinet unit बनाएँएक cabinet unit को शेल्फ़ और वर्टिकल panel से विभाजित करें, फिर बाद में सेक्शन की ऊँचाई समायोजित करें।
- Cabinet properties panel के टैबजानें कि cabinet properties panel को quick access, customize और construction टैब में कैसे व्यवस्थित किया गया है।
- properties panel से core और finish material बदलेंproperties panel से core और finish material बदलें।
- admin portal bulk actions के माध्यम से drawer bottom panel offset बदलेंbulk actions और panel-level edits का उपयोग करके admin portal के माध्यम से drawer bottom panel offset सेट करें, और material के अनुकूल thickness चुनें।
- custom panel और kitchen filler panel type चुनेंLearn which custom panel shapes and kitchen filler panel types you can add to a design.
- wardrobe side panel दृश्यता नियंत्रित करेंनियंत्रित करें कि wardrobe के side panel दिखाए जाएँ या नहीं।
- कैबिनेट के अंदर custom panel के रूप में हेडबोर्ड डिज़ाइन बनाएँएक back panel रखकर और एक तिरछा custom panel जोड़कर कैबिनेट को हेडबोर्ड में बदलें, जिसे आप आकार दें, फिनिश करें और सहेजें।
- Edit Panel Design के माध्यम से panel पर groove एक्सट्रूड करें या cut करेंEdit Panel Design में एक shape जोड़कर और उसे लागू करके panel पर groove या उभरी हुई आकृतियाँ बनाएँ।
- कैबिनेट एडिटिंग panel के टैब में सेटिंग्स खोजेंअपनी आवश्यक सेटिंग तक पहुँचने के लिए Quick Access, Customize और Construction टैब तथा selection tree का उपयोग करें।
- custom panel पर गायब hardware ठीक करेंजब अपेक्षित hardware नहीं बनता, तो panel type, dimension और exposed स्थिति जाँचें।
- Hardware borings केवल उन्हीं panels पर दिखते हैं जिन पर hardware लगाया गया हैसमझें कि cabinet में hardware boring points कहाँ दिखते हैं और कोई अपेक्षित boring point क्यों नहीं दिख सकता।
- layer panel में layers का उपयोग करके items को छिपाएँ या दिखाएँजिस layer पर items हैं, उसकी visibility टॉगल करके पूरे item समूहों को एक साथ छिपाएँ या दिखाएँ।
- split top and bottom panel पर हार्डवेयर ड्रिल कैसे पड़ते हैंजानें कि जब कैबिनेट के top and bottom panel प्रत्येक सेक्शन के टुकड़ों में split होते हैं, तब shutter mechanism हार्डवेयर ड्रिल कैसे रखे जाते हैं।
- custom panel पर hardware rule कैसे लागू होते हैंजानें कि custom panel type को लक्षित करने वाला hardware rule panel के रखे जाने के तरीके और आपके द्वारा सेट की गई component और subcomponent शर्तों के आधार पर कैसे लागू होता है।
- L-corner और pentagonal corner panel पर strip light कैसे काम करती हैL-corner या pentagonal corner unit में एक strip light जोड़ें और यह दो जुड़ी हुई strip बन जाती है, L के प्रत्येक leg के साथ एक।
- wardrobe की चौड़ाई top panel को कैसे प्रभावित करती हैजानें कि wardrobe कब एक ही top panel का उपयोग करता है और कब उसकी चौड़ाई top panel को दो SKU में split कर देती है।
- panel design में copy या move से किसी लाइन को offset करेंकिसी चयनित लाइन को किसी दूरी पर डुप्लिकेट करने के लिए copy चुनें या बिना डुप्लिकेट के उसे स्थानांतरित करने के लिए move चुनें।
- सिंक को काउंटर पर रखें, slanted panel पर नहींसिंक केवल ग्रेनाइट जैसे काउंटर पर ही रखें, और जब slanted या angled panel पर आवश्यकता हो तो मैन्युअली डाला गया plumbing fixture उपयोग करें।
- Outputs settings में unit और panel annotations फिर से असाइन करेंदो में से किसी एक मोड का उपयोग करके अपने outputs में unit और panel label फिर से क्रमांकित करें; पहले पुष्टि करें, क्योंकि यह बदलाव पूर्ववत नहीं किया जा सकता।
- किसी sketch panel को साधारण आयताकार panel में वापस लाएँकिसी sketch panel को उसके Edit Shape toolbar पर Revert का उपयोग करके साधारण आयताकार आकार में वापस बदलें और जारी रखने के लिए prompt की पुष्टि करें।
- panel पर finish grain या texture घुमाएँpanel के material section से panel face पर laminate का grain या texture 0, 90, 180 या 270 डिग्री घुमाएँ।
- Set up blind corner units and the dummy panelBuild a blind corner unit with a dummy panel between the shutter and non-shutter front panel and set its depth.
- panel visibility settings के माध्यम से drawer के side panel चालू या बंद करेंdrawer चुनकर और उसके panel visibility विकल्पों का उपयोग करके drawer के side panel दिखाएँ या छिपाएँ।
- समझें कि carcass कॉन्फ़िगरेशन panel size को कैसे निर्धारित करता हैजानें कि panel size उसी carcass के अनुसार क्यों होता है जो वास्तव में बनाया गया है और ज़रूरत पड़ने पर thickness को कैसे समायोजित करें।
- support panel के लिए unit के पीछे shutterless box का उपयोग करेंदिखाई देने वाले shutter के बिना support structure प्रदान करने के लिए unit के पीछे shutterless box का उपयोग करें।
- ceiling, panel और wardrobe panel पर cutting tool का उपयोग करेंcutting tool को केवल एक सतह प्रकार पर नहीं, बल्कि ceiling, panel और wardrobe panel पर लागू करें।
और गाइड 8
सभी दिखाएँ (8)
- जिस face पर cut बनाया गया है, उसी पर through cut खोजेंकिसी cut को देखने या संपादित करने के लिए उस face पर फ़्लिप करें जहाँ वह बनाया गया था, क्योंकि प्रत्येक panel face को अलग-अलग संभाला जाता है और through cuts अन्यथा केवल 3D view में दिखते हैं।
- curved cut समर्थित नहीं हैं; केवल straight cut ही मशीन किए जा सकते हैंजानें कि कौन से cut मशीन किए जा सकते हैं, ताकि आप curved cut के बजाय निर्धारित गहराई और अंतराल पर wall panel groove की योजना बना सकें।
- front shift से एक एक्सट्रूड किए गए face को ऑफ़सेट करेंएक panel को दूसरी परत के सापेक्ष ऑफ़सेट करने के लिए एक्सट्रूड किए गए आकार के front face को एक दूरी तक shift करें।
- नया connector scenario जोड़ने से पहले सभी मौजूदा connectors हटाएँआवश्यक connector जोड़ने से पहले प्रभावित panels पर सभी मौजूदा connectors हटाने का विकल्प सक्षम करें, ताकि नया scenario panel के connector सेट को स्पष्ट रूप से परिभाषित करे।
- admin portal से groove depth tolerance सेट करेंadmin portal में groove depth tolerance जोड़कर panel width बदले बिना groove की गहराई समायोजित करें।
- property panel में What's New प्रविष्टि खोजेंबाईं ओर के property panel बॉक्स में ऊपर स्क्रॉल करके नीली What's New प्रविष्टि देखें, जो viewport navigation, global preferences और settings वाले उसी panel में है।
- किसी स्थिरता रेल को एक विशिष्ट ऊँचाई पर ले जाएँTranslate Panel से एक ही रेल को ऑफ़सेट करें ताकि वह आपकी इच्छित ऊँचाई पर रहे और अन्य रेल समान दूरी पर बनी रहें।
- scenarios के माध्यम से connector स्वचालित रूप से रखेंकुछ connector scenarios में परिभाषित panel type के आधार पर स्वचालित रूप से रखे जाते हैं।